www
.princetontec.com
ENGLISH
Figure 1 – Switch Operation
Opération de commutation
Betriebsartenschalter
* Princeton Tec calculates total burn time as the time it takes for the light source to produce a
minimum of 0.25 lux at 2 meters. 0.25 lux is about the equivalent of a full moon on a clear night.
* Princeton Tec berechnet die Gesamtbrenndauer bezogen auf eine von der Stirnlampe erzeugte
minimale Beleuchtungsstärke von 0,25 Lux in 2 Meter Abstand. 0,25 Lux entsprechen in etwa
der Beleuchtungsstärke des Vollmonds in einer klaren Nacht.
* Princeton Tec définit la durée totale d’éclairage comme le temps nécessaire à la source
lumineuse pour produire un minimum de 0,25 lux à 2 mètres. 0,25 lux équivaut à peu près à la
luminosité d’une pleine lune dans un ciel nocturne dégagé.
TM
B
OT
LED HEADLAMP
Operating and Maintenance
Instructions
Notice d’utilisation et d’entr
etien
Bedienungsanleitung
Battery Installation – See Battery Installation Diagram
• 2 AAA
• Alkaline (LR03) or Lithium
• Rechargeable NiCad or NiMH
Princeton Tec cares about the environment and
recommends recycling batteries. For more
information about battery recycling, please go
to: www.batteryrecycling.com
To install the batteries, open the battery door.
The battery door has a screw enclosure to
prevent accidental opening. The screw
requires a #1 Philips screwdriver for opening.
Once the screw is unsecured, rotate the
battery door open.
Install two (2) AAA batteries as shown in the
diagram. The tall spring on the battery door
should correspond with the negative polarity
and the shorter spring should correspond with
the positive polarity. Observe proper battery
polarity when installing the batteries. Improper
installation of the batteries will damage the light
and void the warranty.
Rotate the battery door to the closed position.
Using a #1 Philips screwdriver, secure the
battery door shut with the screw. Rotate the
screw down until secure.
WARNING
•
Never mix fresh and used batteries.
•
Never mix different battery brands or
chemistry types.
•
Always remove drained batteries immediately.
•
Remove batteries during long periods of
storage.
NOTE: Rechargeable NiCad or NiMH
batteries may result in reduced brightness
due to lower nominal voltage.
Switch Operation –
See Switch Operation diagram
The first button press turns the light on in low
mode. A second press activates high. A third
push activates the flash mode. Once a mode
has been selected for more than 2 seconds,
the next button press will turn the light off.
The Bot also has an auto shutoff function. After
2.5 hours of uninterrupted operation, the light
will turn itself off.
*The burn times listed on the rear of the
packaging assume you start with fresh
batteries, the light remains on, and you use
only one mode.
Troubleshooting
If the Bot fails to light:
•
Check the batteries for proper installation.
•
Replace batteries if proper installation is
confirmed.
•
Check the light for water contamination on
the circuit board. The light will resume
normal operation once the water is shaken
or blown out and the light is left open until
completely dry. If the light has been
contaminated with salt water, flush the unit
with fresh water and dry as described above.
USA– International 5-Year Warranty
WARRANTY – Princeton Tec warrants this
product to be free from defects in workmanship
and materials under normal use for as long as
you own this product. This warranty covers all
of the component parts of the product except
batteries. This warranty does not cover
deterioration due to normal wear or damage
due to misuse, alteration, negligence,
accidents, or unauthorized repair. Princeton
Tec will repair or replace parts which are
defective in workmanship or materials.
Your authorized Princeton Tec Dealer and
Princeton Tec are the only facilities authorized
to repair the product. After (3) unsuccessful
attempts (within the warranty period) to repair
the product, you have the right to elect
replacement of the product or a refund of the
purchase price less allowance for use of the
product. NO INCIDENTAL OR CONSEQUEN-
TIAL DAMAGES ARE INCLUDED IN THIS
WARRANTY. (Some states do not allow the
exclusion or limitation of incidental or
consequential damages, so the above
limitations or exclusions may not apply to you.)
This warranty gives you specific legal rights,
and you may also have other rights which vary
from state to state.
Princeton Tec reserves the right to change
product specifications without notice.
Return Policy
If your light fails to operate, follow these
simple steps:
1) Check batteries. Replace if necessary.
2) Contact Princeton Tec customer service at
800-257-9080 to request an RMA number to
send your light in for repair or replacement. No
warranty repairs will be accepted without an
RMA number.
3) Return the light without batteries to:
Princeton Tec, 5198 Rt. 130, Bordentown,
NJ 08505. Postage due and freight collect
items will not be accepted.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
www.princetontec.com
© 2013 Princeton Tec
To switch between light
sources, press and hold
button (1-2 seconds)
Figure 2 – Battery Replacement
Remplacement des piles
Einlegen der Batterien
3
1
2
press 1x = Low
press 2x = High
press 3x = Flash
2 Ultrabright
LEDs
DISTANCE (Meters)
15
25
HIGH
4.5H
LOW
9H
FLASH
11H
