Primus D55 Service Manual Download Page 61 | Manualshive

Page: 61 / 82

Primus D55 Service Manual Download Page 61

70276001

59

Section 6 Adjustments

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

73. DRIVE BELT TENSION

NOTE: Belt tension from cylinder drive motor
pulley to step pulley can be measured to ensure
proper installation in one of the following ways:

• Burroughs Belt Tension Gauge initial reading 60-

70 pounds.

• Force to deflect belt .38 inch at midspan with

initial tensioning 6.0 pounds

• Burroughs Belt Tension Gauge reading after run

45-55 pounds.

a. Support drive guard cover and remove screws

holding guard to rear of tumbler. Refer to
Figure 11.

b. Loosen the two motor bracket pivot screws.

Refer to Figure 25.

c. Turn the adjusting nuts clockwise until proper

tension is reached. Refer to Figure 25.

d. Retighten all nuts and screws.

Figure 28

TMB1787S

REAR

BEARING MOUNTING

SCREW

REAR

BEARING ASSEMBLY

COLLAR

FRONT

BEARING ASSEMBLY

COLLAR

FRONT

ADJUSTING

SCREW

REAR

ADJUSTING

SCREW

«
...
59
60
61
62
63
...
»

Summary of Contents for D55



















































































Reviews:

No comments