background image

Im p o rtant Saf e ty Instructi o ns

READ ALL INSTRUCTIONS BEFORE INSTALLATION, OPERATION, OR MAINTENANCE OF PRODUCT.

Some of the following information may not apply to your particular product model; however, as with any electronic product, precautions

should be observed during installation, operation, and maintenance.

l

Installation must conform to state or local building codes and ordinances.

l

Installation or maintenance should be performed only by qualified personnel as defined in the Local Electrical Code.

l

Mount in location where device will not readily be subject to tampering.

l

Any wiring instructions must be followed precisely. Failure to do so could cause permanent equipment damage.

l

To avoid possible electric shock or damage to the device, disconnect power source before installation or servicing.

l

Do not install or use device near water. To reduce the risk of electrical shock, do not expose device to rain or moisture. Device must

not be exposed to dripping or splashing and no objects filled with liquids, such as vases, must be placed on the device.

l

Device is designed for indoor use only. Operating outdoors, or in wet areas, is an electrical hazard and may damage the equipment

while nullifying the warranty.

l

Device is cleanable with a cloth moistened with water or a common disinfectant. Be sure to test any cleaning solutions on a small

area of the clock before using it on the entire device. Do not use caustic cleaners or abrasives.

l

Keep away from dust, dirt and moisture.

l

For healthcare facilities, devices are not intended for patient use and must not be installed within 6 feet (2 m) of patient contact.

AC-Power Models

l

AC main power supply must be disconnected while installing or performing maintenance of any device. To completely disconnect

the power input, the main plug should be disconnected from the main socket outlet completely.

l

The main socket outlet must provide a protective earthing connection where the outlet has a protective earth (ground) connection.

l

Main plug is used as disconnect device and it should remain readily operable during intended use.

l

If power cable is connected directly to junction box without an outlet, AC power must be supplied from a circuit that has a resettable

circuit breaker. AC mains power supply must be disconnected while installing or performing maintenance of any device. Open the

circuit breaker supplying the device before attempting installation, maintenance, or repairs.

4

Summary of Contents for OneVue Smart-Sync
























Reviews: