Unit: mm
Fig. 4
Fig. 5
4
5
6
7
CONNECTION DIAGRAM
Caution! Voltage of heating elements 220-240V
Caution! In the event of any connection the safety
wire must be connected to the
PE terminal.
Recommended
type of
connection
lead
For 220-240V earthed one-phase connection, the bridges
connect L and N terminals, safety wire to
N
L
PE
not to damage the ignition plugs and thermocouples.
on the worktop.
Screw one end of the bracket into the pre-drilled holes in the underside of the hob.
The other end of the bracket should be located underneath the worktop to secure
please follow the below instructions:
Note: The panel underneath the hob must be easily removable to allow for any servicing
requirements.
INSERTING AND FIXING THE HOB
Before inserting the hob into the work surface,
1) Remove the pan stands and burner caps before turning the hob upside down, taking care
2) Place the seal “a” around the bottom edge of the hob as shown in the illustration below.
3) Place the hob in the installation opening and push it down so that the hob is resting firmly
4) Secure the hob in position using the fixing brackets supplied.
the hob in position.
ELECTRICAL CONNECTION
The appliance must be connected to the mains supply by a qualified gas engineer using fixed wiring
via a double pole switched fused spur outlet protected by a 3A fuse and with a contact separation of
We recommend that the appliance is connected by a qualified electrician who is a member of the
N.I.C.E.I.C. and will comply with I.E.T. and local regulations.
at least 3mm in all poles.
This panel must have adequate ventilation to the rear
.
When fitting a gas hob above a drawer or a standard housing unit, suitable precautions must be
taken to prevent contact with the hotplate surface as it can become very hot during operation.
The recommended method is to fix a wooden panel within the cabinet at a distance of 15mm below
the underside of the hob (Fig. 6).
INSTALLATION OPTIONS
The wires in the mains lead are coloured in accordance with the following code: Green & Yellow = Earth,
Blue = Neutral, Brown = Live.
Fig. 9
Fig. 10
INJECTOR REPLACEMENT TABLE
A
B
D
C
E
E
G
F
BURNERS
NORMAL
PRESSURE
NORMAL
RATE
INJECTOR
DIAMETER
NOMINAL HEAT
INPUT (kW)
DESCRIPTION
GAS
mbar
kW
1/100 mm
MIN.
1
2
3
RAPID
BUTANE
PROPANE
NATURAL
28-30
37
20
85
85
118
SEMI-RAPID
BUTANE
PROPANE
NATURAL
28-30
37
20
68
68
97
AUXILIARY
BUTANE
PROPANE
NATURAL
28-30
37
20
50
50
73
1.2
1.2
0.8
0.8
0.8
0.6
0.6
0.6
3.0
3.0
3.0
1.75
1.75
1
1
1
1.2
1.75
4
2.6
2.6
2.6
3.8
3.8
3.8
100
100
135
TRIPLE
FLAME
BUTANE
PROPANE
NATURAL
28-30
37
20
SELECT THE RIGHT BURNER
Use an appropriately sized pan with a flat bottom for each burner (see the table below and Fig.12).
NOTE: Matches can be used to light the burners in the event of a power failure.
N
NO
OTTE
E: Please do not use pots or pans that overlap the boundaries of the hob.
Keep the control knob pressed in for 15 seconds ensuring the burner stays lit when released.
When the contents of the pan start to boil, turn the knob down to reduced rate position. Always
Fig.11
Fig.12
Closed position
maximun position
minimum position
If the burner fails to stay lit wait for 1 minute before relighting.
put a lid on the pan.
Burners
3000W
Semi-rapid
1750 W
Auxiliary
1000W
φ
Pans (cm)
20
24
-
-
22
26
16-18
10-14
Rapid
Triple Flame
3800W
Check the guide below if there is a problem with the hob.
UNEVEN OR YELLOW FLAME RATHER THAN BLUE.
Switch off and check the following points:
1. Are the burners fitted correctly?
2. Are the holes in the burner clear?
3. Check that no dust has fallen into the flame turning it yellow.
BURNER FAILING TO IGNITE?
Check that the power is turned on or that the fuse has not blown.
Make sure that the ignitor is not coated with food spillage.
SPARK BUT NO GAS?
Make sure the gas is turned on.
Check that the burner holes are not blocked.
SMELL GAS?
Check to see if any gas taps have been left on.
If they are off, switch the gas off at the mains and call a service agent.
WARNING! DO NOT check with a naked flame, strike any matches
or press ignitor.
STILL NOT WORKING?
Call a service agent.
7. TROUBLESHOOTING
ATTENTION
！
Consult the instruction manual before
proceeding with installation or use of
the appliance.
8. TECHNICAL INFORMATION
A) Measurement and calculation methods
● These gas hobs are CE approved according to the Gas Appliance Directives 2009/142/EC.
● The energy efficiency of these gas hobs was tested and measured according to EN 30-2-1-1998+A1-2003+A2-2005.
● The semi-rapid burner and rapid burner were tested separately; the auxiliary burner was not required for the test because its
nominal heat input is less than 1.16kW.
● The energy efficiency of the gas burners and the hob were calculated according to the COMMISSION REGULATION (EU)
No. 66/2014.
B) Rational Use of Energy and the Appliance
● The gas hobs are designed for domestic use only; commercial use will invalidate the warranty.
● The gas hobs are designed for use with gas (either Natural or LPG). The combustion process produces carbon monoxide
and carbon dioxide gases.
● To ensure energy saving, please install the gas hob according to the instructions provided in Section 5. Please ensure that
you use the correct pan for each burner.
● To ensure safe use, please read this instruction booklet carefully before using the appliance and strictly follow the operation
and maintenance guidelines. Do not attempt to modify the appliance under any circumstances.
● Please contact the after sales service for repair and/or exchange of components (such as gas valves, control knobs) if
necessary.
● The packaging of this product is recyclable.
S
S
Detach the seals from their backing ensuring that the transparent protection still adheres to the seal.
Turn the hob over and correctly position seal *S* (Fig. 5) under the edge of the hob so that the outer
part of the seal perfectly matches the outer edge of the hob. The ends of the strips must fit together
without overlapping. Fix the seal to the hob evenly and securely, pressing it firmly in place.
GAS CONNECTION (QUALIFIED PERSONNEL ONLY)
The gas inlet fitting for these appliances is a ½” male threaded conic gas type, complying with ISO 7-1
standards. Please ensure that the connection is made using a rigid pipe.
When making the gas connection, it is important to place the gasket (A) in between the inlet pipe (C) and the
elbow (B) to ensure a tight gas seal (Fig. 8).
6. USER INSTRUCTIONS
1. To light the hob, push down the appropriate knob and turn anti-clockwise to the large flame
symbol (Fig.11).
2. Keep the knob depressed until the burner lights.
3. Turn the knob to the required setting.
4. In the event of the burner flames being accidentally extinguished, turn off the burner immediately
and do not attempt to reignite for at least 1 minute.
This appliance must be installed in
compliance with the current
regulations and only installed in rooms
equipped with adequate ventilation.
A
B
C
D
M
Ventilation slot ≥ 30mm.
15mm MIN.
Fig. 6
Worktop
Fixing bracket
Screw
Fig. 8
N
L
NATURAL GAS TO LPG CONVERSION
This conversion must only be carried out by a competent person (i.e. a Gas Safe registered fitter).
Instructions to fit replacement injectors:
1. Disconnect the appliance from the gas and electrical supplies.
2. Remove burner components “B” and pan supports (Fig. 9).
3. Remove the injectors “A” (Fig. 9) with a socket spanner and replace with the corresponding injectors.
Setting up minimum flow rates:
1. Turn on the LPG supply, light the burners and turn the controls to the minimum position as indicated by the
small flame symbol.
2. Remove the control knobs “M” (Fig. 10).
3. Insert a small screwdriver “D” (Fig. 10) into the hole at the top of the tap “C” and turn the adjustment screw left
or right until the flame of the burner is conveniently regulated to the low position.
4. Make sure when turning quickly from maximun position to minimum position that the flame does not extinguish.
5. Replace the knobs “M”.
ENERGY EFFIECIENCY INFORMATION
A B C D E F G
557 477 65 62 150min 90min 750min
Model
EE
gas burner
EE
gas hob
Small
(Auxiliary)
Medium
(Semi-rapid)
Big (Rapid)
Triple
56%
56%
N/A
54%
56.5%
56.5%
55.5%
56%
B
A
C
N/A
N/A
Fig. 7
35cm
4cm
S
S
Worktop
Fixing bracket
Screw
In the case of built-in hotplates, where the manufacturer specifies that a horizontal separation shall be
included below the base of the hotplate, the critical dimensions of this separation. In addition, the
minimum distance declared shall not exceed 150mm;
Prolonged intensive use of the appliance may call for additional ventilation, for example opening of a
window or more effective ventilation, for example increasing the level of machanical ventilation where
present.
CAUTION: Accessible parts may be not when the grill is in use. Young children should be kept away.
CAUTION: This appliance is for cooking purposes only. It must not be used for other purposes, for
example room heating.
1
1
2
2
2
2
4
4
3
PRGH212
PRGH214
Correct Disposal of This Product:
This marking indicates that this product should not be disposed of together with other
household waste. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote sustainable re-use of
material resources. To return your unwanted product, please use local return and
collect systems or contact the retailer where the product was purchased. They
should be able to take the appliance for environmentally-safe recycling.
