9
11) PRIORITY CHANNELS
Priority channels will be automatically
selected
by switching this key (
11
).
3 positions switch:
EMG1
/ Priority channel 1 is activated.
EMG2
/ Priority
channel 2 is activated.
OFF /
No priority channel is activated.
The default priority channels are channel
9
(
EMG1
) and channel
19
(
EMG2
).
See the
EMG SET 1
and
EMG SET 2
menus page 11 to
set
priority channels.
Note:
Activating a priority channel no longer allows you to use the
PA
or
WX
modes, or to start the
SCAN
function. if the
KEY BEEP
function is active, an
error beep is emitted.
“EMG”
and the channel blink to indicate unauthorized
handling. Turn the switch (
11
) to the
OFF
position to use these functions.
12) CB/PA
Switch between
CB
and
PA
(Public Address) mode.
An external optional speaker can be connected to the unit to the PA.SP.
jack on the rear panel. (
D
). Turn the
MIC GAIN
knob (
4
) to adjust the
PA
volume.
For details on operating in PA mode, see the
PA SETTING
menu on page
12.
13) WX MODE ~ ALERT
WX MODE
(short press)
Note:
CB
functions are not allowed in
WX
mode. If a user presses a not al-
lowed key when the
KEY BEEP
function is activated, the radio sounds an error
tone.
Select a channel other than the
EMG1
or
EMG2
emergency channels. The
PRIORITY CHANNEL
switch (
11
) must be in the
OFF
position. Press briefly the
WX
key (
13
) to alternate between
CB
and
WX
modes. When
WX
mode is
active,
“WX”
is displayed.
WX
mode allows you to listen to weather reports.
When this mode is turned on, turn the rotary
PUSH
knob (
6
) or use the
UP
/
DN
(
18
) keys on the microphone to search, through the 7 weather channels,
for the channel corresponding to your location
(See
WEATHER FREQUENCY
TABLE
page 55)
.
The display shows the selected channel.
ALERT
(long press)
Note:
The SIREN tone
only sounds in
PA
or
CB
mode. It does not sound in
WX
mode.
Long press the
ALERT
key (
13
), to
activate
/
deactivate
the
ALERT
function.
When the function is activated the last digit of frequency becomes
A
(
). If the function is activated and a tone is detected at
the selected weather channel, then the unit sounds “SIREN” tone. The unit
cancels
CB
or
PA
mode and goes to
WX
mode.
During a SIREN tone sound, press
PTT
key (
17
) to stop the sound.
14) BARGRAPH
Indicates
the reception level and the emitted power level.
15) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the
setting of the equipment into the dashboard easier.
See Cabling Diagram page 56.
16) USB CHARGING SOCKET
The
USB
socket (
16
) can be used to charge smartphones, tablets or other
rechargeable devices with 5 V - 2.1 A.
17) PTT
Transmission key, press to
transmit
a message,
is displayed and release
to
listen to
an incoming communication,
disappears.
TOT (Time Out Timer)
If the
PTT
switch (
17
) key is pressed for more than 5 minutes, the display starts
blinking and the transmission
ends
. A beep will sound until the
PTT
switch
(
17
) key is released.
18) UP/DN BUTTONS ON MICROPHONE ~ SCAN
UP/DN BUTTONS ON MICROPHONE
(short press)
In normal use, press
UP
/
DN
buttons (
18
) on the microphone to
change
the
channel.
UP
to
increase
and
DN
to
decrease
the channel.
In
MENU
mode [press the
PUSH
knob (
6
) for about 3 seconds to activate this
mode
(see §
MENU
page 10)
], the
UP
or
DN
buttons (
18
) allows to
select
the menu to be set.
See
ROTARY “PUSH” KNOB
page 7
.
English
Summary of Contents for WALKER II FCC
Page 59: ......