12
CHECK BATTERY CAPACITY
1. Turn on the booster MPB-12000, slide
ON/OFF
(
7
) to
“ON”
.
2. Press
POWER
(
5
) without any devices connected to the charger.
3. The number of bars in the battery icon on the display (
1
) indicate how much power is in the MPB-12000.
4. Turn off the booster MPB-12000, slide
ON/OFF
(
7
) to
“OFF”
.
JUMP START A VEHICLE
1. Make sure the booster MPB-12000 is fully charged.
2. Turn off all accessories on the vehicle (radio, air conditioner, etc.)
3. Connect the jumper cable’s
RED
clamp to the
POSITIVE
(
+
) post of the vehicle battery.
4. Connect the jumper cable’s
BLACK
clamp to the
NEGATIVE
(
-
) post of the vehicle battery.
5. Insert the jumper cable connector into the 12 V connector (
8
) of the booster MPB-12000. Be sure the
connection is solid.
6. Turn on the booster MPB-12000, slide
ON/OFF
(
7
) to
“ON”
.
7. Turn the vehicle ignition key for 3 seconds maximum.
If the vehicle starts:
• Disconnect the jumper cables from the MPB-12000 first (
8
), then disconnect the clamps from the
battery.
If the vehicle does not start:
• Wait 1 minute and try again.
8. Turn off the booster MPB-12000, slide
ON/OFF
(
7
) to
“OFF”
.
CHARGING A 5 V USB DEVICE (TABLET, CELL PHONE, ETC.)
1. Turn on the booster MPB-12000, slide
ON/OFF
(
7
) to
“ON”
.
2. Connect the 2-1 USB cord to the USB output (
3
) of the booster MPB-12000
3. Connect your device to either the mini USB or micro USB cable.
4. The MPB-12000 begins to charge your device. It will put on standby at the end of the charge.
5. Turn off the booster MPB-12000, slide
ON/OFF
(
7
) to
“OFF”
.
TURN ON FLASHLIGHT
1. Turn on the booster MPB-12000, slide
ON/OFF
(
7
) to
“ON”
.
2. Press and hold
POWER
(
5
) to turn on the LED flashlight.
3. Short press
POWER
(
5
) again to cycle through the 4 modes: Steady / Strobe S.O.S / Fast Strobe /
OFF.
4. Turn off the booster MPB-12000, slide
ON/OFF
(
7
) to
“OFF”
.
POWER / CHARGE 12, 16 OR 19 V DC DEVICES
1. Turn on the booster MPB-12000, slide
ON/OFF
(
7
) to
“ON”
.
2. Short press
POWER
(
5
) to cycle through the 3 DC voltage values: 12 V / 16 V / 19 V. See
“OUT2”
in
the display (
1
).
3. Insert the connector cable (not included) into the output jack (
4
) of the booster MPB-12000 to power /
charge the electronics device.
The voltage value cannot be change while a cable is connected to the output jack (4).
4. When finished, turn off the booster MPB-12000, slide
ON/OFF
(
7
) to
“OFF”
.
COMPACT TIRE INFLATOR
• This is not a toy. Please keep out of reach of children
• Do NOT leave the compressor unattended when in use
• Make sure to stay safe and away from traffic if you have to inflate tires at roadside
• Do not use the compressor in explosive atmospheres, in the presence of flammable liquids, gases or
dust
• Do not expose the compressor to rain or wet conditions
• In case of electrical or mechanical malfunction, immediately switch off the compressor and unplug it
• Over-inflation may cause items to burst which could cause injury. Do NOT attempt to over-inflate.
• The compact tire inflator cannot be serviced by the user.