49
Press
F
key (
9
).
is displayed.
Long press
F
key (
9
) to
enter
the
MENU
.
OPERATING MODE
1.
Turn the rotary
CH
knob (
6
) or use the
UP/DN
buttons (
13
) on the microphone
to
select
the
menu.
2.
Briefly press the
EMG
key (
5
) to
confirm
. The operating mode flashes (
Id
or
DF
).
3.
Turn the rotary
CH
knob (
6
) or use the
UP/DN
buttons (
13
) on the microphone
to
select
the desired operating mode.
STORING A CTCSS/DCS CODE
Depending on the operating mode used, the procedure differs:
Identical mode
Id
4.
A short press on the
EMG
key (
5
) makes the genre blink (
“CTCSS”
,
“DCS”
or
“
OFF
”
no genre).
5.
Turn the rotary
CH
knob (
6
) or use the
UP/DN
buttons (
13
) on the microphone
to
select
the genre or…
6.
Press the
EMG
key (
5
) to
confirm
the genre. The code value flashes (unless
OFF
selected).
7.
Turn the rotary
CH
knob (
6
) or use the
UP/DN
buttons (
13
) on the microphone
to
select
the code (from 01 to 38 for CTCSS and 001 to 104 for DCS).
Different Mode
DF
4.
A short press on the
MENU
key (
4
) makes the type
RX
blink.
5.
Turn the rotary
CH
knob (
6
) or use the
UP/DN
buttons (
13
) on the microphone
to
select
the
RX
or
TX
type.
6.
A short press on the
EMG
key (
5
)
validates
the choice of type. The genre
value flashes (
“CTCSS”
,
“DCS”
or
“
OFF
”
no genre).
7.
Turn the rotary
CH
knob (
6
) or use the
UP/DN
buttons (
13
) on the microphone
to
select
the genre or…
8.
Press the
EMG
key (
5
) to
confirm
the genre. The code value flashes (unless
OFF
has been selected).
9.
Turn the rotary
CH
knob (
6
) or use the
UP/DN
buttons (
13
) on the microphone
to
select
the code (01 to 38 for CTCSS 001 to 104 for DCS).
10.
Press the
EMG
key (
5
) to
confirm
the selected code. The unit return to point
5
, for set the second type.
11.
If you don’t need to set the second type, long press the
EMG
key (
5
) to
validate
and exit the
MENU
.
12.
If no key is pressed, the device
exits
the
MENU
after 10 seconds without
saving
the changes.
The default mode is
Id
(Identical). The default genre is
OFF
.
See the
RESET
menu
.
14) REPEATER / RELAY setting
WARNING! This function is valid only on the D frequency band
.
See the
configuration table page 74
.
This function allows you to
increase
the range of your CB.
The radio receives on the current channel
RX1
and transmits on the selected
channel
TX2
.
1.
Select the
RX1
channel.
2.
Press
F
key (
9
).
is displayed.
3.
Long press
F
key (
9
) to
enter
the
MENU
.
4.
Turn the rotary
CH
knob (
6
) or use
UP
/
DN
buttons (
13
) on the microphone
to
select
the
menu.
5.
Short press on the
EMG
key (
5
). The current transmission channel
RX2
blinks
on the display.
6.
Turn the rotary
CH
knob (
6
) or use
UP
/
DN
buttons (
13
) on the microphone
to
select
the transmission channel (
TX2
) or
Id
(identical, no repeater).
7.
New press on the
EMG
key (
5
) to
validate
.
a)
Return to the point
1
to set
another menu or
b)
Short press the
F
key (
9
) to
validate
and
exit
the
MENU
.
disappears from the display.
8.
If no key is pressed, the unit
exits
MENU
after 10 seconds.
disappears
from the display.
The default transmission channel is
1d
(identical RX channel).
To activate the function, see the §
REPEATER/RELAY
page 45
.
15) RESET
This function allows to
Erase
the scan skip memory or
restore
all factory
settings.
Press
F
key (
9
).
is displayed.
Long press
F
key (
9
) to
enter
the
MENU
.
1.
Turn the rotary
CH
knob (
6
) or use
UP
/
DN
buttons (
13
) on the microphone
to
select
the
menu.
2.
Press
EMG
key (
5
) to
validate.
The current value
blinks on the display.
English