45
3.
When the configuration is selected, press the
F
key (
9
) during 1 second. The
letter corresponding to the configuration is continuously displayed and a
confirmation beep sounds.
4.
At this point, confirm the selection by switching off the transceiver and then
switching it on again.
See the frequency bands table at pages 70 to 72 / configuration table
page 74.
D) FUNCTIONS WITH THE PTT SWITCH
1) TALKBACK
This function allows you to
hear
your own modulation in the optional internal
or external speaker connected to the EXT.SP jack (
E
).
Press and hold the
PTT
switch (
12
) then press the
F
key (
9
) to
activate
/
deactivate
the
TALKBACK
function.
When the function is active,
“TALKBACK”
blinks on the display for 3 seconds,
displaying the current level of the
TALKBACK
and then remains permanently
displayed.
2) TALKBACK LEVEL
This function allows to adjust the volume level of the
TALKBACK
.
1.
Activate the
TALKBACK
function.
2.
Press and hold the
PTT
switch (
12
) then turn the rotary
CH
knob (
6
) to
in-
crease
(clockwise) /
decrease
(counterclockwise) the volume level of the
TALKBACK
.
3.
Release the
PTT
switch (
12
).
3) NOISE GATE
(PTT + VOX)
-
Press and hold the
PTT
switch (
12
).
-
Short press the
VOX
key (
10
) to
activate
(
On
) or
deactivate
(
OF
) the
NOISE
GATE
. “
” is displayed when the function is active.
Noise Gate:
Prevents amplification of background noise. This results in
optimized signal levels.
4) REPEATER / RELAY
(PTT + AM/FM)
WARNING! This function is valid only on the D frequency band
.
See the
configuration table page 74
.
This function allows you to increase the range of your transceiver.
The radio receives on the current channel and transmits on the defined
channel.
To activate this function you must define a TX channel
(See
REPEATER/RELAY
SETTING
menu page 49)
.
-
Press and hold the
PTT
switch (
12
).
-
Short press the
AM/FM
key (
4
) to
activate
or
deactivate
the
REPETER/RELAY
function
. The selection or
“
”
, if the transmission
channel has not still been selected, blinks during 3 seconds.
E) MENU
The order of 15 menus is as described in this manual. However, the menu
displayed by entering the
MENU
will be the last menu modified by user.
The procedure is the same whatever the function is:
Press
F
key (
9
).
is displayed.
Long press
F
key (
9
) to
enter
the
MENU
.
1.
Turn the rotary
CH
knob (
6
) or use
UP
/
DN
buttons (
13
) on the microphone
to
select
the menu to set.
2.
Press
EMG
key (
5
) to
validate.
The current color blinks on the display.
3.
Turn the rotary
CH
knob (
6
) or use
UP
/
DN
buttons (
13
) on the microphone
to
modify
the value of the parameter.
4.
New press on
EMG
key (
5
) to
validate
the chosen value. The parameter
stops blinking and if the function has more than one parameter, the next
parameter blinks.
5.
If no key is pressed, the unit
exits
MENU
after 10 seconds.
disappears
from the display.
Note:
UP/DN
buttons (
13
) on the microphone have the same effect as the
rotation of the rotary
CH
knob (
6
).
PTT
switch (
12
)
validates
the last setting
and
exists
MENU
.
disappears.
1) COLOR
Press
F
key (
9
).
is displayed.
Long press
F
key (
9
) to
enter
the
MENU
.
1.
Turn the rotary
CH
knob (
6
) or use
UP
/
DN
buttons (
13
) on the microphone
to
select
the
menu.
2.
Press
EMG
key (
5
) to
validate.
The current color
blinks on the display.
3.
Turn the rotary
CH
knob (
6
) or use
UP
/
DN
buttons (
13
) on the microphone
to
modify
the color of the display.
English