44
VOX SETTING
(long press)
1.
Long press the
VOX
key (
10
) to
enter
the
VOX SETTING
.
“VOX”
blinks, the
current setting and its value appear on the display. Three parameters allow
to adjtust the
VOX
: Sensitivity
/ Anti-vox level
/ Vox delay
time
.
2a.
Turn the
ROTARY
knob (
6
) or use the
UP/DN
key (
13
) on the microphone
to
modify
the current parameter then, press the
F
key (
9
) to
select
next
parameter or....
2b.
Press first the
F
key (
9
) to
select
another the parameter and then turn the
ROTARY
knob (
6
) or use the
UP/DN
key (
13
) on the microphone to
modify
the current parameter.
3.
When all adjustments are done, press
PTT
switch (
12
) to
store
and
exit
. If the
KEY BEEP
function is activated, a long beep sounds to
confirm
the success
of the operation
(consul the
KEY BEEP
menu page 46)
.
4.
If no key is pressed for 10 seconds, the unit automatically
exits
the function
VOX SETTING
without
save
.
-
Sensitivity
: allows the adjustment of the microphone (original one
or optional vox) for an optimum transmission quality. Adjustable level from
1
(high level) to
9
(low level). Default value:
5
.
-
Anti-Vox
: allows disabling the transmission generated by the sur-
rounding noise. The level is adjustable.
AF
(according the squelch level)
and from
0
(without anti-vox) to
9
(low level). Default value:
AF
.
-
Delay
time
: allows avoiding the sudden cut of the transmission by
adding a delay at the end of speaking. The level is adjustable from
1
(short
delay) to
9
(long delay). Default value:
1
.
VOX SETTING
doesn’t activate the
VOX
function.
11) 6 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the
setting of the equipment into the dashboard easier.
See Cabling Diagram page 73.
12) PTT (Push To Talk)
Transmission key, press to
transmit
a message,
is displayed and release
to
listen to
an incoming communication,
disappears.
TOT (Time Out Timer)
If the transmission using
PTT
switch (
12
) or VOX function is longer than 3
minutes, the display starts blinking and the transmission
ends
. A beep will
sound until the
PTT
switch (
12
) key is released.
13) UP/DN BUTTONS ON MICROPHONE ~ SCAN
UP/DN BUTTONS ON MICROPHONE
(short press)
Press
UP
/
DN
buttons (
13
) on the microphone to
change
the channel.
UP
to
increase
and
DN
to
decrease
the channel.
See
ROTARY KNOB
page 43
.
SCAN
(very long press)
Press and hold the
UP
or
DN
button (
13
) for ± 7 seconds or until a beep
sounds
(consult the
KEY BEEP
menu page 46)
to
activate
the
SCAN
func-
tion.
“SCN”
appears on the display. The scanning stops as soon as there is
a busy channel.
Consult the
SCAN TYPE
menu page 47.
In
SCANNING
mode, turn the
ROTARY
knob (
6
) or press the
UP
/
DN
buttons (
13
) on the
microphone to
change
scan direction.
Press
PTT
switch (
12
) to
exit
SCAN
.
“SCN”
disappears on the display.
See the
§
SKIP
page 43
.
5 + 9) KEY LOCK
(EMG + F keys)
Long press simultaneously the
EMG
(
5
) and
F
(
9
) keys to
activate
/
deactivate
the
KEY LOCK
function. When the function is active,
“
”
appears on the
display.
A) DC-POWER TERMINAL (13.2 V / 26.4 V)
B) ANTENNA CONNECTOR (SO-239)
C) JACK FOR OPTIONAL VOX MICROPHONE (Ø 2.5 mm)
D) PA SPEAKER JACK (8
Ω
, Ø 3.5 mm)
E) JACK FOR EXTERNAL OPTIONAL SPEAKER (8
Ω
, Ø 3.5 mm)
C) FUNCTIONS TURNING ON THE UNIT
1) FREQUENCY BAND SELECTION
(
Configuration: EU; PL; d; EC; U; In
)
The frequency bands have to be chosen according to the country of use.
Don’t use any other configuration. Some countries need a user’s licence.
See table page 75
.
1.
Turn on the power while pressing the
F
key (
9
). The letter corresponding to
the current configuration is blinking.
2.
In order to change the configuration, use the
ROTARY
knob (
6
) on the unit
or the
UP
/
DN
buttons (
13
) on the microphone.
English