INSTALLATION STEPS: 2-Handle Lavatory Faucet
Shut off water supply at angle stop. Remove
old faucet. Clean sink surface in preparation
for new faucet.
1.
Ensure the gasket (1) is on the bottom
of the new faucet (2). Place the faucet
(2) through the mounting holes in the
sink. Secure the faucet (2) to the sink
using the mounting nuts (3) provided.
Hand-tighten only.
Option: If the sink is uneven, use the
silicone under the gasket (1).
2.
Cleaning:
To maintain and protect the fine luster of all products, clean with a soft, damp cloth
only. DO NOT USE detergents or cleansers as they may harm the protective finish.
Model Number: 3552613 / 3552611
INSTALLATION
7.If the horizontal rod (1) is too long, as
shown in Fig 1, the length can be adjusted.
Remove the clip (2) from the horizontal rod
(1). Slide the plastic portion of the rod to
adjust to the desired length. The excess
length (3) can be removed by snapping off
with pliers at the perforated segment, or cut
off with a saw. After the plastic portion is
positioned properly, reinstall the clip (2) as
shown in Fig 3. NOTE: If the horizontal rod
of the pop-up assembly is too long, do not
cut as it can be adjusted.
Tools:
Adjustable Wrench
Groove Joint Pliers
Pipe Wrench
Screwdriver
Thread Sealant Tape
Basin Wrench
Plumber's Putty
Slide the lift rod (1) through the faucet
assembly (2) until the knob rests on the
faucet assembly. Push the pivot rod (3)
to the down position until the stopper (4)
is completely open. Press the button (5)
on the slip joint assembly (6) and adjust
the vertical rod (7) up or down and front
or back along the pivot rod (3) until the
vertical rod (7) is in the correct position
to engage with the lift rod (1). Press lift
rod (1) into the top of the vertical rod (7)
until it engages. Operate the lift rod (1)
up and down to verify that the stopper
opens and closes correctly.
8.
Remove the stopper (1) and flange (2).
Screw the the nut (3) all the way down
and push the gasket (4) down.
4.
5. Apply silicone to the underside of the
flange (1). Insert the pop-up body (2)
into the sink. Screw the flange (1) onto
the pop-up body (2). The pivot hole (3)
must face the back of the sink. Use the
groove joint pliers to tighten the nut (4),
but do not overtighten. Do not turn the
pop-up body (2) while tightening the nut
(4), or the sealant may not seal properly.
Clean away any excess putty. Open the
easy-install rotating clip (5).
close
open
wall
1
2
3
4
1
2
3
4
5
1
2
3
4
5
6
7
Fig 1
Fig 2
Fig 3
1
2
3
1
2
1
1
3
2
Important: After installation is completed,
remove the aerator. Do not lose the gasket
(1) in the aerator. Turn on the water supply
and allow both hot and cold water to run
for at least one minute each. This flushes
away any debris that could cause damage
to internal parts. While the water is running,
check for leaks. Turn off the water and
replace the aerator.
9.
2
1
3
3
5
6
2
4
1
7
5
6
3
1
Making the waterline connections:
Use 1/2" IPS faucet connections (2, not
included), or use the coupling nuts (3, not
included) with a 3/8" OD ball-nose riser
(1, not included). Use wrenches when
tightening. Do not overtighten.
6.Install the horizontal rod (1) and stopper
(2) as shown (3) and (4). Make sure the
horizontal rod (1) inserts into the pop-up
body (5) completely as shown (6). Close
the easy-install rotating clip (7).