INSTALLATION STEPS: Single handle lavatory faucet
Cleaning:
To maintain and protect the fine luster of all products, clean with a soft, damp cloth
only. DO NOT USE detergents or cleansers as they may harm the protective finish.
INSTALLATION
Model Number: 284443 & 284445 & 284446
Making the waterline connections:
Use 1/2 in. I.P.S. faucet connections (2, not included),
or use the coupling nuts (3, not included) with a 3/8 in.
O.D. ball-nose riser (1, not included).
NOTE: The hot side inlet tube is indcated by a label.
If the label is not present, the hot supply tube is the
longer of the two inlet tubes.
Flange Installation (optional).
Shut off the water supply at angle stop. Remove the
old faucet. Clean the sink surface in preparation for
new faucet. Place the flange (1) on the bottom of the
new faucet.
Install the faucet assembly through the
holes of the sink. From underneath the sink, secure
the faucet to the sink with the washers (2) and nut (3)
provided.
Before tightening the faucet connector to the
water supply, apply a second wrench to the
supply tube fitting. This will prevent the supply
tube from moving or twisting when tightening
the faucet connector. Do not overtighten.
3.
1.
2.
1
2
3
1
3
2
7
8
3
11
10
4
5
6
9
2
1
Remove the stopper (1) and the flange (2). Screw
the brass nut (3) all the way down. Push the plastic
washer (4) and the gasket (5) down. Unscrew the
pivot nut (6) from the pop-up body (7) and remove
the seal washers (8). Take off the spring clip (9)
from the horizontal rod (10). Remove the tailpiece
(11) from the pop-up body (7).
4.
5
4
3
1
2
5. Apply the silicone to the underside of the flange
(2). Insert the pop-up body (1) into the drain hole
from below sink. Screw the flange (2) into the
pop-up body (1). With the pivot hole (3) facing
toward faucet, Use groove joint pliers to tighten
the nut (4), do not over tighten. Do not turn the
pop-up while tightening the nut, or sealant may
not seal drain. Clean excess putty.
Apply thread
sealant tape to the top threads of the tailpiece (5)
in a clockwise direction, as shown and hand
tighten.
4
3
2
1
Install the horizontal rod (2) and the stopper (3) as
shown (4). Hand tighten the pivot nut (1).
6.
3
2
5
1
4
Place one end of the spring clip (1) onto the end
of the horizontal rod (2). Insert the horizontal rod
(2) through a hole on the strap (3). Connect the
other end of the spring clip (1) to the horizontal
rod (2). Insert the lift rod (4) into the strap and
tighten the screw (5).
7.
Important: After installation is completed, turn on the water
supply and allow both hot and cold water to run for at least
one minute each. This flushes away any debris that could
cause damage to internal parts. While the water is running,
check for leaks. Turn off the water.
9.
1
Escutcheon Installation (optional).
Shut off the water supply at angle stop. Remove
the old faucet. Clean the sink surface in
preparation for new faucet. Place the escutcheon
(1) and
the base plate (2) on the bottom of the
new faucet.
Install the faucet assembly through
the holes of the sink. From underneath the sink,
secure the faucet to the sink with the washers
(3) and nut (4) provided.
3
4
2
1.
Brand Lavatory Faucets
Tools:
Adjustable wrench
Groove joint pliers
Pipe wrench
Screwdriver
Thread sealant tape
Basin wrench
Plumber's putty
