background image

3

W a r n i n g !

A m p l i f i e r s   G e n e r a t e   H e a t !
You can mount the 

MA2150  in any position, even upside-down. However, you

must maintain proper airflow. Do not install your 

MA2150 under carpets or enclose

it behind airtight panels. In trunk-mounted applications, be sure to provide venting
for air circulation. Let the amplifier breathe. Without adequate air circulation, your
Tube Driver will reduce its power output to protect itself.

P o w e r   W i r e   C a l c u l a t o r

M o u n t i n g

You need to mount your 

MA2150  securely in your vehicle to prevent damage. You

may mount the system right-side up, on its side, or upside-down, provided there is
adequate ventilation.

Recommended MINIMUM Gauge

       

20 - 35

       12      10

      8

     8

    6

  6

8

4

     

  0 - 20

       14      12

    12

   10

  10

  8

8

8

    

  35 - 50

       10       8

      8

     6

    6

  4

4

4

    

  50 -  65

        8       8

      6

     4

    4

  4

4

2

   

   65  -  85

        6       6

      4

     4

    2

  2

2

0

      

85 - 105

        6       6

      4

     2

    2

  2

2

0

   

 105 - 125

        4       4

      4

     2

    2

  0

0

0

    

125 - 150

        2       2

      2

     2

    0

  0

0

0

Total Current Draw

Length of Wire to Run  (in Feet)

     (in Amps)

         < 3       4 - 7    7 - 10  10 - 13   13-16    16-19    19-22     22-28

BACK TO  CONTENTS

Summary of Contents for MA2150




















Reviews: