Precision Digital Corporation PD6900 Series, Instruction Manual

Page: 15 / 82

PD6928 Ex-Proof & I.S. Loop-Powered Flow Rate/Totalizer Instruction Manual
15
Enclosure
Material AL Models:
ASTM A413 LM6 die-cast aluminum,
copper-free, enamel coated.
-SS Models:
ASTM A743 CF8M investment-cast
316 stainless steel
Gasket Fluoroelastomer
Rating NEMA 4X, IP68 explosion-proof
Color -AL: Blue; -SS: Silver
Window Borosilicate glass
Conduits Two ¾" NPT threaded conduit openings.
M20 conduits are available. See
Ordering
Information on page 12 for details.
Flange Built-in flange for wall and pipe mounting.
Tamper-Proof
Seal Enclosure lid may be secured with
tamper-proof seal.
ATEX &
IECEx
(Enclosure
only) Flameproof protection
II 2GD
Ex db IIC Gb
Ex tb IIIC Db
IP66/IP68
Tamb: -55°C to +85°C
Certificate No.: Sira 19ATEX1252U
Certificate No.: IECEx SIR 19.0075U
CSA
(Enclosure
only) Class I, Division 1, Groups A, B, C, D
Class II, Division 1, Group E, F, G;
Class III
Ex db IIC Gb
Ex tb IIIC Db
Class I, Zone 1, AEx db IIC Gb;
Zone 21, AEx tb IIIC Db
IP66/IP68/TYPE 4X
Tamb: -55°C to +85°C
Certificate No.: 80011200
UL
(Enclosure
only) Class I, Division 1, Groups A, B, C and D
Class II, Division 1, Groups E, F and G
Class III;
Class I, Zone 1, AEx db IIC Gb
Zone 21, AEx tb IIIC
Ex db IIC Gb
Ex tb IIIC Db
IP66/IP68/TYPE 4X
Tamb: -55°C to +85°C
Certificate Number: E518920
Input
Input 4-20 mA
Accuracy ±0.02% of span ±1 count, Square root and
programmable exponent: 10-100% FS
Voltage Drop Without backlight: 1.5 V maximum,
With backlight: 4.7 V maximum
Equivalent
Resistance Without backlight: 75
Ω @ 20 mA
With backlight: 235
Ω @ 20 mA
Input
Overload Over current protection to 1 A maximum,
Over voltage protection to 30 VDC max
(Between mA+ and mA- / BL-)
Temperature
Drift 25 PPM/°C from -40 to 75°C ambient
Function Rate: Linear (2-32 points), square root, or
programmable exponent
If the totalizer is disabled, PV1 and PV2: Linear
(2-32 points) or round horizontal tank
Low-Flow
Cutoff 0.1 to 999,999 or disable. Point below at which
the display always shows zero.
HART
Transparency The meter does not interfere with existing
HART communications; it displays the
4-20 mA primary variable and it allows the
HART communications to pass through
without interruption. The meter is not affected if
a HART communicator is connected to the
loop. The meter does not display secondary
HART variables.
Rate/Totalizer
Rate Display
Top display: -9999 to 99999;
Bottom display: -9,999,999 to 99,999,999
(with commas)
Total & Grand
Total Display Top display: 0 to 99999;
Bottom display: 0 to 99,999,999
(with commas)
13-Digit Total
& Grand Total Up to 9,999,999,999,999 using both lines
with 13-digit total feature enabled.
Total Decimal
Point Up to four decimal places on top, up to seven
decimal places on bottom. Total decimal
point is independent of rate decimal point.
Totalizer Calculates total based on rate and rate units
to display total in engineering units. A custom
factor must be programmed if using custom
defined units.
Time Base Seconds, Minutes, Hours, Days
Totalizer
Rollover Totalizer rolls over when display exceeds
99,999,999 (9,999,999,999,999 if 13-digit
limit enabled). Relay status reflects display.
Total & Grand
Total Reset Via CapTouch button, external contact
closure on digital input, or MeterView XL.
Total & Grand
Total Reset
Passwords Total and grand total passwords may be
entered to prevent resetting the total or grand
total unless a password is entered.
Non-
Resettable
Grand Total Grand total reset may be disabled through
the meter interface. Grand total reset may be
permanently disabled by selecting
YES
at the
PERMLOCK
menu.
•
Once the Grand Total has been programmed as
“non-resettable” the feature
CANNOT be disabled.
Non-Volatile
Memory Total and Grand Total values are stored in
non-volatile memory for a minimum of ten
years if power is lost.