L-PROG
L-AC
0V 110V 220V
BOT
- 12V +
TR + BAT -
110V
220V
ELECTRICAL NETWORK
12V BATTERY
N.A. BUTTON
ON OFF
PROG
05
10
30
60
ELECTROMAGNETIC
LOCK
EMERGENCY
KEY
PERIPHERAL 12V
BUZZER
05
10
30
60
SELECT THE ACTIVATION TIME
05, 10, 30 AND 60 SECONDS
IDENTIFICATION OF 0V/110V/220V TERMINALS:
Input from the electrical network (local network), to the equipment.
To connect the equipment to 110V, use the
terminals: 0V and 110V.
To connect the equipment to 220V, use the
terminals: 0V and 220V.
12V +/- :
12V output used to power peripherals
(sensors, alarm panels, etc).
Output Voltage:
13.8Vdc
Max output current:
3A
BAT +/-:
Input for 12V/7Ah battery.
The power supply has a floating charging system that keeps the
battery at full charge at all times.
BOT:
Use (
BOT and 12V-
), to connect the NO button, to activate
the electromagnetic lock.
TR:
Used to power the electromagnetic lock (
TR and 12V-
).
IDENTIFICATION OF JUMPERS
BUZZER:
When the option
ON
is selected, whenever the lock is
activated, the source will emit an audible signal through the same
time interval set for activation.
When the option
OFF
is activated, it will turn off the sound option
of drive.
Jumpers
05, 10, 30, 60:
Select a fixed time in second of drive.
REMOTE CONTROL:
To program the remote control, perform the following steps:
Step 1:
Press and hold the '
PROG
' button consequently
the '
L-PROG
' will light up.
Step 2:
Press any key on the remote control until the
'
L-PROG
' flashes 3 times, indicating that the recording has
been success, this procedure should be performed as
soon as possible as quickly as possible to avoid writing
unwanted codes.
PS:
Up to 42 controls can be recorded in the source, when all 42
controls are recorded, every time you try record a new control,
the '
L-PROG
' will flash indicating that font memory is full.
To delete the font memory, perform the following steps:
Step 1:
Completely turn off the power supply.
Step 2:
Press and hold the '
PROG
' button and reefed the board
the '
L-PULSO
', will light up for 1 second indicating that the
memory has been deleted..
P30528 - 09/2022
Rev. 0
Manual
SS 400 CR
POWER SUPPLY 12V
WITH BATTERY CHARGER
Made by:
Motoppar da Amazônia Indústria e Comércio de Eletrônicos LTDA
Praça Linear, 100, Bloco 2 - Centro
Santa Rita do Sapucaí - MG - CEP 37.540-000 - Brasil
CNPJ: 09.084.119/0002-45
www.citrox.com.br | +55 14 3407 1000
CX-8118
ATTENTION:
Do not use the equipment
without rst reading the
instruction manual.
GENERAL TERMS AND CONDITIONS OF WARRANTY
MOTOPPAR da Amazônia Indústria e Comércio de Eletrônicos Ltda, registered with
CNPJ No. 09.084.119/0002-45, located at Praça Linear, No. 100, Bloco II, Centro,
Santa Rita do Sapucaí/MG, CEP 37.500-000, manufacturer of the PPA and CITROX
products, guarantees this device against defects in design, manufacture, assembly
and/or jointly and severally as a result of defects in the quality of the material that
make it inappropriate or unsuitable for the consumption for which it is intended, for
a legal period of 90 (ninety) days from the date of purchase, provided that the
installation guidelines described in the instruction manual are observed.
As a result of the credibility and trust placed in PPA AND CITROX products, we
added another 275 days to the above period, reaching a total of 1 (one) year, also
counted from the date of purchase to be proven by the consumer through the
proof of purchase (Supervisor Note).
In the event of a defect, within the warranty period, the liability of PPA and/or
CITROX is restricted to the repair or replacement of the device manufactured by it,
under the following conditions:
1.
The repair and readjustment of the equipment can only be carried out by the
Technical Assistance, which is quali ed to open, remove, replace parts or
components, as well as repair the defects covered by the warranty, and, in the
absence of this and any use of parts not originals contained in the use, will
result in the waiver of this term by the consumer;
2.
The warranty will not extend to accessories such as cables, screws kit, xing
brackets, sources, etc.;
3.
Expenses for packaging, transport and reinstallation of the product are
exclusively borne by the consumer;
4.
The equipment must be sent directly to the company responsible for the sale,
representative of the manufacturer, through the address on the purchase
invoice, properly packaged, thus avoiding the loss of warranty;
5.
The replacement or repair of the equipment does not extend the warranty
period.
This warranty will be void if the product:
1.
Suffer damages caused by agents of nature, such as atmospheric discharges,
oods, res, landslides, etc.;
2.
It is installed in an improper electrical network or even in disagreement with
any of the installation instructions set out in the manual;
3.
Defects caused by falls, blows or any other physical accident;
4.
For violation of the equipment or attempt to repair by unauthorized
personnel;
5.
It is not used for its intended purpose;
6.
Not used under normal conditions;
7.
Suffer damage caused by accessories or equipment attached to the product.
Recommendation:
We recommend the installation and maintenance of the product by a specialized
technical service.
If the product has a defect or abnormal operation, look for a specialized Technical
Service for the necessary corrections.
