PowerVent 43VP40E2 Page 20 Use And Care Manual Download

Page: 20 / 40

This.PowerVent.water.heater.contains.an.accessory.kit.for.

installing.the.User.Display .
User.Display.Mounting.Kit.–.AS42461
.

a ....Optional.Water.Heater.Mounting.Bracket.–.

AP14752

b ...12.feet,.18.AWG.Thermostat.Wire.–.AP14820

c ...Optional.Mounting.Tape.–.AP14819

d ...Transformer.Enclosure.–.AP14875

e ....Screw,.#8.x.½".Self.Drilling.qty.2.AP5925GS

f ...User.Display.–.AP14697

Installation.Instructions:

CAUTION:..Turn.the.switch.on.the.blower.to.the.

“off”.position.and.disconnect.power.to.the.water.heater.

before.proceeding!
1 ....Locate.the.electrical.connection.for.the.Transformer.

Enclosure.on.the.top.of.the.water.heater ...This.

electrical.connection.features.a.white.6-pin.plug.and.

white.heat.shrink .

2 ....The.Transformer.Enclosure.features.a.6-pin.connection.

located.on.the.circuit.board.inside.the.enclosure ...

Attach.the.top.pan.harness.connector.to.this.6-pin.

connector.in.the.correct.orientation .

3 ....Locate.the.two.screw.pilot.holes.on.the.water.heater.

top.to.attach.the.Transformer.Enclosure.to.the.top.pan ...

Position.the.enclosure.so.the.terminal.strip.opening.

is.visible.from.the.front.of.the.water.heater ...Secure.

enclosure.to.top.pan.with.screws.provided.in.the.User.

Display.Mounting.Kit.without.pinching.any.wires .

NOTICE: Do not over tighten to avoid cracking

plastic enclosure.

4 ....Determine.where.the.User.Display.will.be.located ...

The.display.can.be.attached.to.the.water.heater.jacket.

with.supplied.Water.Heater.Mounting.Bracket.or.

mounted.remotely.to.a.wall.via.the.wall.plate.up.to.100.

feet.away.using.18.AWG.solid.copper.thermostat.wire ...

Any.installation.location.over.12.feet.from.the.water.

heater.will.require.additional.thermostat.wire ...(Not.

supplied .)

5 ....If.remote.mounting,.go.to.step.19 .
6 ....Cut.enough.thermostat.wire.from.the.12.feet.

provided.to.connect.the.front.mounted.display.to.the.

Transformer.Enclosure.located.on.the.top.pan .

7 ....Strip.½”.insulation.from.the.3.wires.on.both.ends ...

The.wire.provided.is.standard.3-wire.with.the.colors.

GREEN,.RED.and.WHITE .

8 ....Connect.one.end.of.the.wire.to.the.Transformer.

Enclosure.spring.terminal.strip ...From.left.to.right.

colors.shall.be.GREEN.–.RED.–.WHITE ...Wires.

should.easily.insert.into.the.terminal.strip ...If.required.

for.wire.insertion.or.removal,.use.small.flat.blade.

screw.driver.to.press.the.tab.located.below.each.wire.

hole .

9 ....Remove.two.strips.of.Display.Mounting.Tape.and.

attach.to.the.inside.flanges.of.the.Water.Heater.

Mounting.Bracket .

Installing the Optional User Display

Transformer

Pin.Plug

6.Pin.Connection.for.to.

Circuit.Board

Mounting.Holes.for.

Transformer

Display.Mounting.

Tape.Strips

Water.Heater.

Mounting.Braket.

for.Display

Flange.of.Mounting.

Bracket

Summary of Contents for 43VP40E2









































Search results

Summary of Contents for 43VP40E2

Reviews:

Related manuals for 43VP40E2

Brands by name

Popular brands

PowerVent 43VP40E2, Use And Care Manual

Search results

Summary of Contents for 43VP40E2

Reviews:

Related manuals for 43VP40E2

Brands by name

Popular brands