Connecting Garden Hose. Refer to page 8 of
the operator’s manual for more details.
4
Use labels to identify and match parts. Then
attach the end of the garden hose to the water
intake of the pump.
Installing the Handle. Refer to page 8 of the
operator’s manual for more details.
Insert both sides of handle until pins click.
1
A
Remove fuel cap. Insert funnel. Fill tank to
approximately 1-1/2 in. below the top of the tank
neck. Replace cap.
Use 87 Octane gasoline only.
Do not mix oil with
gasoline.
Do not use E85 (Ethanol 85).
Adding gasoline. Refer to page 10 of the
operator’s manual for more details.
3
A
Adding/checking oil. Refer to page 9 of the
operator’s manual for more details.
2
To add oil: Unscrew oil tip from oil bottle, then remove
foil seal. Replace oil tip. Remove oil cap from pressure
washer, then add oil by squeezing the entire contents
of the oil bottle into the oil reservoir.
To check oil: Remove dipstick and wipe clean.
Replace dipstick, but do not rethread. Remove
dipstick again and observe oil level. Oil level should fall
within the hatched area on dipstick. Replace oil cap.
A
Garden
Hose
Connecting High Pressure Hose to Pump. Refer to
page 8 of the operator’s manual for more details.
5
High Pressure
Hose
Use labels to identify and match parts. Then insert
the end of the high pressure hose into the threaded
nipple on the pump. Turn clockwise to tighten.
A
Connecting High Pressure Hose to Trigger Handle.
Refer to page 8 of the operator’s manual for more
details.
Screw the collar on the high pressure hose into
the trigger handle inlet coupler by turning the hose
collar clockwise.
6
A
Assembling the Trigger Handle. Refer to page
8 of the operator’s manual for more details.
Insert threaded end of spray wand into the
connector on the end of the trigger
handle. Turn connector clockwise
until it stops.
Engage the lock-out when the
pressure washer is not in use.
7
A
B
25
Using the Nozzles. Refer to page 11 of the operator’s
manual for more details.
Turn the Water Faucet Completely
On. Do not run the pump without
the water supply connected and
turned on.
Pull collar back.
Push tip into
quick-connect.
Release collar and it will click
into place
8
9
A
B
C
Squeeze and Hold
the Trigger for
Thirty Seconds
to relieve excess
pressure trapped
in the system
.
10
B
A
C
A
B
Verify that the Choke Pin is Pulled All the Way
OUT. (The position of the Choke Pin has been preset
by the factory to be fully out.)
After Starting Push Choke Pin in Gradually Until
Engine Runs Smoothly.
Pull the Recoil Starter Refer
to page 10 of the operator’s
manual for more details.
Give the recoil starter 3 - 4
short, brisk pulls to start the
engine. If the engine doesn’t
start after 4 pulls, call customer
service at 1-877-617-3501. Do
not return to store.
12
14
13
11
A
Verify that the On/Off Switch is in the ON
Position. (The On/Off switch is preset by the
factory to be in the ON position.)
Verify that the Fuel Valve is in the OPEN
position. (The Fuel Valve is preset by the
factory to be in the OPEN position.)
OPEN
CLOSE
ON
PS80979 QUICK START GUIDE
(NOTE: Page references refer to the Operator’s Manual)
WARNING:
This Quick Start Guide is not a substitute for reading the
operator’s manual. To reduce the risk of injury or death,
user must read and understand operator’s manual before
using this product.
TM
988000-519
6-7-11 (REV:02)
Do Not Return To Store. For assistance with anything that has to do with this unit please call the
numbers or visit the website listed below.
PowerStroke Customer Service 1-877-617-3501 M – F 8am – 5pm, Sa/Su 8am – 4pm (EST) (excluding
holidays)
www.powerstroketools.com
A
