12
3. Make sure insert the switch key.
4. Press the primer bulb 3 times.
5. Pull on the recoil starter handle slowly until a slight resistance is felt, then pull quickly to start the
engine. Return cord gently into the recoil starter. Never allow the cord to snap back.
6. If engine fails to start, repeat step 4. NOTE: After repeated failed attempts to start the engine, please
consult the troubleshooting guide before attempting again. If problems persist, please call customer
service.
7. Once the engine has started, slowly return the choke lever all the way to the “OPEN” position.
8. Allow the engine to run for several minutes before cleaning snow. This allows the engine to stabilize
its speed and temperature.
ELECTRIC START THE ENGINE
To start the engine using the electric start function, perform the following steps:
1. Check the oil and gas levels.
2. Move the choke lever to the “CLOSE” position.
3. Make sure insert the switch key.
4. Press the primer bulb 3 times.
5. Plug the power cord to starting motor.
6. Press the start button for 2-3 seconds or until the engine starts. NOTE: If the engine does not start
after 2-3 seconds, release the start button.
7. If engine fails to start, wait 10 seconds, then repeat step 6. NOTE: After repeated attempts to start the
engine, please consult the troubleshooting guide before attempting again. If problems persist, please
call customer service.
8. Once the engine has started. Slowly move the choke lever all the way to the “OPEN” position. Allow
the engine to run for several minutes before attempting to clean snow.
CLEARING SNOW
Start the engine once your snow thrower has been running outside for several minutes, it is now ready for
use. Make sure the path in front of your Snow Thrower is free from people, animals, objects, and all other
obstructions except for snow.
Adjust the chute outlet to the desired direction.
Turn the chute rotation handle clockwise or counter-clockwise until the desired position is reached.
WARNING!
Never direct the chute outlet toward people or animals. While snow may seem harmless, it can
contain rocks or other debris that can cause serious injury when projected through the chute.
1.
Engage/depress the auger control lever (handle) to start the augers and impeller turning.
2.
Set the desired direction and speed using the speed/gear control lever.
3.
Engage/depress the drive control lever (handle) and direct the snow thrower into the snow to be cleared.
NOTICE: NEVER
change speed/gear positions while the drive control lever (handle) is engaged.
Disengage the drive control handle BEFORE changing speeds or directions. If the snow is deeper
than the height of the auger, remove it in several steps taking narrower swaths. Make several passes
with the auger overlapping the cleared areas and reduce forward speed.
For the best clearing efficiency, clear snow before it melts, refreezes and hardens. Hard
packed and wet snow can be very difficult to clear.
Clearing wet heavy snow can be a challenge, depending on ambient temperature, humidity levels, and
overall climate conditions including actual snow conditions, there may be no 100% solution as snow
may be too wet or compacted to move or throw. Wet snow will tend to clog and stick more to the augers
and chute. Keep the auger engaged as much as possible when clearing wet snow to help prevent
clogging.
WARNING!
If snow is filled with foreign material, damage to the snow thrower may result.
Avoid snow with foreign materials.
STOPPING
Summary of Contents for PSSHD24T
