background image

 

PERSONAL SAFETY 

 

 

Engine exhaust, and certain vehicle components contain or emit chemicals known to cause cancer, 
birth defects or other reproductive harm. 

 

 

Read, understand and follow all instructions on your snow thrower unit and in this instruction manual 
before attempting to assemble and operate your machine. 

 

 

Keep this instruction manual in a safe place for future and regular reference. If replacement parts are 
needed, refer to the Panel, Chute, Frame and Housing Diagrams and Parts’ Listings on pages 25-30. 

 

 

Stay alert, watch what you are doing and use common sense when operating your snow thrower unit. 

 

 

Do not use your snow thrower unit while you are tired or under the influence of drugs, alcohol, 
medication. A moment of inattention while operating the snow thrower may result in severe bodily 
injury. 

 

 

NEVER LEAVE YOUR RUNNING SNOW THROWER UNATTENDED

Stop the engine!

 

 

 

Do not leave your snow thrower unit until it has come to a complete stop. 

 

 

When stepping backwards, be cautious about any obstacles beneath your feet or behind you avoid 
falling. 
 

 

SERVICE 

 

 

Stop the engine before making any adjustments. Check for misalignment, breakage or binding of 
moving parts, and any other conditions that may affect operation. 

 

 

If damaged, have the snow thrower unit serviced by an authorized service center using only specified, 
manufactured replacement parts. This will ensure that the safety of the snow thrower unit is 
maintained. 

 
 

SAFE HANDLING OF GASOLINE 

 
To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is 
extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is 
spilled on yourself or your clothes which can ignite, therefore wash your skin and change clothes 
immediately. 
 

 

Use only an approved gasoline container. 

 

 

Extinguish all cigarettes, cigars, pipes and other sources of ignition. 

 

 

Never fuel snow thrower unit’s engine indoors. 

 

 

Never remove gas cap or add fuel while the engine is hot or running. 

 

 

Allow engine to cool at least two minutes before refueling. 

Summary of Contents for DB7651SL

































Reviews: