ENGLISH
SETUP:
1. Connect the included AC adapter to the DC input
located on the bottom of the Charging Station.
2. Place charging station near an easily accessible
wall-outlet.
3. Plug the included AC adapter into your wall outlet.
CHARGING YOUR DUALSHOCK®4 CONTROLLERS:
The Charging Station can charge one or two
DUALSHOCK®4 controllers.
• Dock your DUALSHOCK®4 controller by placing
it over the Charging Station’s charge cradle and
aligning the Charging Station’s connectors with
your controller’s charge input.
• Place the DUALSHOCK®4 controller onto the
charging cradle and push down. The cradle
will click into place to indicate the controller is
properly docked.
• If the DUALSHOCK®4 controller you’re charging
isn’t currently connected to your PlayStation®4
console, it will illuminate orange to indicate
charging. Once charging is complete, the
DUALSHOCK®4 controller illumination will turn
off. If the DUALSHOCK®4 controller is currently
connected to the PlayStation®4 system, the
controller colour will not change to indicate
charging status. Charging status can be checked
in the PlayStation®4 interface.
To remove your DUALSHOCK®4 controller, press
down on the controller. The cradle will release your
controller.
TROUBLESHOOTING:
For current FAQs, visit www.PowerA.com/support
Q: Why are my controllers not charging?
A: Confirm your Charging Station AC adapter is
connected to both the Charging Station and your
wall outlet.
A: Confirm your controllers are properly docked on
the Charging Station.
A: Your controller might already be fully charged.
SUPPORT:
For assistance with authentic PowerA accessories,
please email PowerA@ bdainc.com or call (888)
664-4327 from 5 AM–5 PM PST. PowerA, the PowerA
logo, and “Amplify Your Experience” are trademarks
of Bensussen Deutsch and Associates, Inc. TM and
© Bensussen Deutsch and Associates, Inc.
Manufactured & distributed under license by
Sony Computer Entertainment Europe.“
”, “PlayStation”, “DUALSHOCK” are registered
trademarks of Sony Computer Entertainment
Inc. Also, “
” is a trademark of the same
company. All rights reserved.
REGIONAL COMPLIANCE SYMBOLS:
More information available via web-search of each
symbol name.
The WEEE symbol informs the end-user
about separate disposal requirements for
WEEE (Waste of electrical and electronic
equipment) as required per the Article
11(2) of the WEEE Directive and prescribed by
European standard EN50419:2005.
CE (Conformité Européene aka European
Conformity) is a certification mark that
indicates conformity with health, safety, and
environmental protection standards for products
sold within the European Economic Area.
The Regulatory Compliance Mark is a
visible indication of a product’s
compliance with all applicable ACMA (Australian
Communications and Media Authority) regulatory
arrangements, including all technical and
record-keeping requirements regarding the
electrical safety and/or electromagnetic
compatibility (EMC).
WARRANTY:
2-Year Limited Warranty:
Visit PowerA.com for
details.
FCC AND IC NOTICE:
Warning:
Changes or modifications to this unit
not expressly approved by the party responsible
for compliance could void the user’s authority to
operate the equipment.
Note:
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures: Reorient or relocate the receiving
antenna. Increase the separation between the
equipment and receiver. Connect the equipment into
an outlet on a circuit different from that to which
the receiver is connected. Consult the dealer or an
experienced radio/TV technician for help.
IC CLASS B:
This device complies with Industry Canada license-
exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference, and (2)
this device mustaccept any interference, including
interference that may cause undesired operation of
the device. This Class B digital apparatus complies
with Canadian ICES-003.
AUSTRALIAN WARRANTY STATEMENT:
This product comes with guarantees that cannot
be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a
major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure
does not amount to a major failure. If purchased
within Australia or New Zealand, this product comes
with a one-year warranty from date of purchase.
Defects in the product must have appeared within
one year from date of purchase, in order to claim the
warranty. All warranty claims must be facilitated
back through the retailer of purchase in accordance
with the retailer’s return policies and procedures.
Any expenses incurred, as a result of returning
the product to the retailer of purchase are the full
responsibility of the consumer.
AU WHOLESALE DISTRIBUTOR:
Bluemouth Interactive Pty Ltd Level 2, 2 Darling
Street South Yarra, VIC 3141, Aus61 (3)
9867 2666
MANUFACTURED BY:
Bensussen Deutsch & Associates, Inc. (BDA, Inc.)
15525 Woodinville-Redmond Rd. NE Woodinville, WA
98072 www.bdainc.com
FRANÇAIS
INSTALLATION:
1. Connectez l’adaptateur CA inclus à l’entrée CC
située en bas de la station de chargement.
2. Placez la station de charge près d’une prise
murale facile d’accès.
3. Branchez l’adaptateur CA sur une prise murale.
CHARGEMENT DE VOS CONTRÔLEURS
DUALSHOCK®4:
La station de chargement peut charger un ou deux
contrôleurs DUALSHOCK®4 à la fois.
• Placez votre contrôleur DUALSHOCK®4 sur le
socle de la station de chargement et alignez
les connecteurs de cette dernière à l’entrée de
chargement de votre contrôleur.
• Positionnez le contrôleur DUALSHOCK®4 sur le
socle de chargement en appuyant dessus. Un clic
sur le socle vous indiquera que le contrôleur est
correctement positionné.
• Si la manette sans fil DUALSHOCK®4 que vous
chargez n’est pas connectée à votre console
PlayStation®4, la barre lumineuse de la manette
Press down to remove controllers
Connect the AC adapter
Dock your controllers
3
1
2
Customer Service
Service client / Kundendienst / Servicio a clientes
/ Assistenza clienti / Apoio ao Cliente
Customer [email protected]
2-Year Limited Warranty: Visit PowerA.com for details and to register your product
Garantía limitada de 2 años. Visita PowerA.com para obtener detalles y para registrarte.
Garantia limitada de 2 anos: Visita PowerA.com para obter detalhes e registar o teu produto
Beschränkte 2-Jahres-Garantie – Details und Informationen zur Anmeldung finden Sie unter PowerA.com.
Garantie limitée de 2 ans – Rendez-vous sur PowerA.com pour de plus amples informations et pour enregistrer votre achat.
Garantia limitada de 2 anos: Visita PowerA.com para obter detalhes e registar o teu produto
CHARGING
STATION
USER MANUAL
Manuel de l’utilisateur, Bedienungsanleitung,
Manual de usuario, Manuale per l’uso,
Manual do usuário
BDA Inc.
15525 Woodinville-Redmond Rd NE
Woodinville, WA 98072
