manualshive.com logo in svg

Power integrations Scale-2 1SC0450E2B0, Applications Manual, Page: 22 / 25

Share
Download
Power integrations Scale-2 1SC0450E2B0 Applications Manual Download Page 22

SCALE™-2 1SC0450E2B0 

   

 

Preliminary Description & Application Manual 

 

www.power.com/igbt-driver 

Page 22 

Bibliography 

/1/

 

Paper: Smart Power Chip Tuning, Bodo’s Power Systems, May 2007 

/2/

 

“Description and Application Manual for SCALE™ Drivers”, Power Integrations 

/3/

 

Data sheet SCALE™-2 driver core 1SC0450E2B0, Power Integrations 

/4/

 

Application  note  AN-1101:  Application  with  SCALE™-2  and  SCALE™-2+  Gate  Driver  Cores,  Power 

Integrations 

/5/

 

Application note AN-0904: Direct Paralleling of SCALE™-2 Gate Driver Cores, Power Integrations 

/6/

 

Application  note  AN-0901:  Methodology  for  Controlling  Multi-Level  Converter  Topologies  with 
SCALE™-2 IGBT Drivers, Power Integrations 

/7/

 

Paper:  Safe  Driving  of  Multi-Level  Converters  Using  Sophisticated  Gate  Driver  Technology,  PCIM 

Asia, June 2013 

Note

:   The Application Notes are available on the Internet at 

www.power.com/igbt-driver/go/app-note

 and 

the papers at 

www.power.com/igbt-driver/go/papers

. 

 

 

Summary of Contents for Scale-2 1SC0450E2B0


























Reviews:

No comments