background image

Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com

3

DISCHARGE

2” NPT, Female, Vertical

LIQUID 

TEMPERATURE

200°F (93°C) Continuous High Temperature

SOLIDS HANDLING

1/2” Solids through strainer. 

2” without strainer

VOLUTE

Cast Iron, Class 30

MOTOR HOUSING

Cast Iron, Class 30, w/removable upper 

chamber for ease of capacitor and cord 

replacement

IMPELLER

2 Vane, open with pump out vanes on back side

Material: Cast Iron, Class 30

SHAFT

Stainless Steel

SEAL PLATE

Cast Iron, Class 30

SQUARE RINGS

Buna-N

HARDWARE

Stainless Steel

PAINT

Powder Coated - Industrial Grade

SEAL

Inboard Single Mechanical, Oil Filled ,

Material: Type 21, Silicon Carbide/Buna-N

Secondary Exclusion Seal

POWER CORD

15 Ft. Cord, Plug on 115 Volt, Pressure 

Grommet for Sealing and Strain Relief

MOTOR

Oil Filled, Squirrel Cage Induction

Class H Insulation, Vacuum Pressure 

Impregnated (VPI)

SINGLE PHASE

Permanent Split Capacitor (PSC),

Includes Overload Protection in Motor:

115v, 50A, Trip Off Temp. 293°F (145°C), 

Closing Temp. 226°F (108°C)

UPPER BEARING

Single Row, Ball, Oil Lubricated

LOWER BEARING

Single Row, Ball, Oil Lubricated

SLUDGE STRAINER

Bar Strainer with 3” extended feet

LEVEL CONTROL

Wide Angel, High Temperature Mechanical 

Float. 15Ft. cord with piggy-back plug. 

Normally Open (N/O)

Specifications - High Temp

MODEL

HP Hz Volts/

Ph

RPM Full Load 

Amps

Locked 

Rotor Amps

NEMA Start 

Code

Winding Resistance

MAIN -- START

Cord 

Type

Cord 

Size

Cord 

O.D.

PFS411HTCE-2 4/10 60 115/1 1750

10.0

24.5

N

1.6 -- 18.5

SJOOW

16/3 0.325

Series:  PFS411HTCE-2

4/10 HP • 1750 RPM • 60 Hz

High Temperature

Submersible Sewage Pump

PFS411HTCE-2    

 

 

          Submersible Effluent, Sump & Sewage Pumps

Summary of Contents for PFS411HTCE-2 Series













Reviews: