-- 9 --
STARTING A COLD ENGINE
1. Move throttle lever to the
position.
2. Move choke lever to the FULL CHOKE posi-
tion.
3. Slowly press the primer button 8 times.
Throttle Lever
Choke Lever
Primer Button
4. Pull starter rope sharply until engine at-
tempts to run, but no more than 5 pulls (be-
low 30
_
F, 8 pulls).
NOTE:
If engine attempts to start before the
5
th
pull, go to next step immediately.
5. Move the choke lever to the HALF CHOKE
position.
6. Pull the starter rope sharply until the engine
runs, but no more than 5 pulls (below 30
_
F,
10 pulls).
7. After a 5 second warm--up, move the choke
lever to the RUN position.
8. Allow the unit to run for 30 more seconds at
the RUN position before moving the throttle
lever to the
position.
If engine has not started after 5 pulls (at HALF
CHOKE), repeat STARTING A COLD ENGINE
procedure. If engine still does not start, proceed
to STARTING A FLOODED ENGINE.
9. To stop the engine, move the throttle lever to
the STOP position.
STARTING A WARM ENGINE
NOTE:
If fuel tank is empty, add fuel; then,
follow STARTING A COLD ENGINE proce-
dure. Do not fill fuel tank while engine is hot.
1. Move throttle lever to the
position.
2. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
NOTE
:
If engine has not started, pull starter
rope 5 more pulls. If engine still does not run,
it is probably flooded.
3. To stop the engine, move the throttle lever to
the STOP position.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing the
choke lever in the RUN position. Move throttle
lever to the fast position
; then, pull rope
until engine starts. After engine starts, move the
throttle lever to the slow position
to allow
engine to idle.
Starting could require pulling the starter rope
many times depending on how badly the unit is
flooded.
If unit still doesn’t start refer to the TROUBLE-
SHOOTING TABLE or call 1-800-554-6723.
MAINTENANCE
WARNING:
Avoid touching muffler
unless engine and muffler are cold. A hot
muffler can cause serious burns.
WARNING:
Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
HELPFUL TIP
IMPORTANT:
Have all
repairs other than the rec-
ommended maintenance
described in the instruction
manual performed by an
authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, Poulan PRO may not pay for
repairs under warranty. It is your re-
sponsibility to maintain and perform
general maintenance.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
CHECK FOR LOOSE
FASTENERS AND PARTS
S
Spark Plug Boot
S
Air Filter
S
Housing Screws
S
Muffler
CHECK FOR DAMAGED OR WORN
PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S
Fuel Tank -- Do not use unit if fuel tank shows
signs of damage or leaks.
S
Vacuum Bag -- Do not use vacuum bag if it
is torn or damaged.
INSPECT AND CLEAN UNIT AND
DECALS
S
After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
decals using a damp cloth with a mild deter-
gent.
S
Wipe off unit with a clean dry cloth.
