Poulan Pro 545047541 Instruction Manual Download

Page: 1 / 18

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e en-

strucciones de seguridad. El no hacerlo puede resultar en lesiones

graves.

AVERTISSEMENT:

Lire le manuel d’instructions et bien respecter tous les avertisse-

ments et toutes les instructions de sécurité. Tout défaut de le faire

pourrait entraîner des blessures graves.

EN
G

LIS

FR
ANÇAI

545047541

5/27/05

For Occasional Use Only

Electrolux Home Products, Inc.

1030 Stevens Creek Road

Augusta, GA 30907

2005 Electrolux Home Products, Inc.

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

Please do not return unit to retailer.

Por favor, no devuelva el aparato al lugar de compra.

Veuillez ne pas retourner l’outil au détaillant.

1--800--554--6723

www.poulan.com

BH 2660

Electrolux Consumer Outdoor Products

5855 Terry Fox Way

Mississauga, Ontario L5V 3E4

Summary of Contents for 545047541



















Search results

Summary of Contents for 545047541

Reviews:

Related manuals for 545047541

Brands by name

Popular brands

Poulan Pro 545047541, Instruction Manual

Search results

Summary of Contents for 545047541

Reviews:

Related manuals for 545047541

Brands by name

Popular brands