Pottinger VITASEM A 251 Operator'S Manual Download

Page: 65 / 82

- 65 -

0600_GB-Power-Control_8537

POWEr COnTrOL - OPErATiOn

Sensor test

The sensor test enables all sensors, the servomotor and
the onboard voltage to be checked.

Press

“Special menu” key

• Menu base setting appears

- Select menu level using arrow keys

Sensor test

- Confirm with OK

In the first screen check the sensors for:

driving lane, seed shaft, hectare meter and level:

- Metal on front of sensor:

bar to ON

- No metal in front of sensor:

bar to OFF

- Switch to second screen: press arrow keys

- Back to main menu: press ESC

In the second screen check the sensors for:

blower and calibration flaps:

- The actual position of the servomotor and the

onboard voltage is shown

- In addition the electro-cylinder can be moved

manually

- Switch to first screen: press arrow keys

- Back to main menu: press ESC

Summary of Contents for VITASEM A 251



















































































Search results

Summary of Contents for VITASEM A 251

Reviews:

Related manuals for VITASEM A 251

Brands by name

Popular brands

Pottinger VITASEM A 251, Operator'S Manual

Search results

Summary of Contents for VITASEM A 251

Reviews:

Related manuals for VITASEM A 251

Brands by name

Popular brands