Pottinger VITASEM A 251 Operator'S Manual Download

Page: 62 / 82

- 62 -

0600_GB-Power-Control_8537

POWEr COnTrOL - OPErATiOn

Stutter switch

With the stutter switch, when putting down the driving
lane, the lane is not left open over the entire length but
alternately seeded and left open.

Example: With a symmetrical cycle the left tractor lane
is seeded for 5m while the right tractor lane is left open.
After the 5m lanes are changed so that the right lane is
seeded and left is left open, etc.

The section length must be entered into the operating
device.

Press

“Special menu” key

• Menu base setting appears

- Select menu level using arrow keys

Stutter switch

- Confirm with OK

• Enter section length with +/- keys
- Length settings of between 2 and 20 m

- Confirm with OK

Switching the function on and off
The function is switched on or off with the “Stutter switch

on/off” key

- As soon as it is switched on two vertical broken

lines appear next to the driving lanes meter.

Summary of Contents for VITASEM A 251



















































































Search results

Summary of Contents for VITASEM A 251

Reviews:

Related manuals for VITASEM A 251

Brands by name

Popular brands

Pottinger VITASEM A 251, Operator'S Manual

Search results

Summary of Contents for VITASEM A 251

Reviews:

Related manuals for VITASEM A 251

Brands by name

Popular brands