background image

- 12 -

1100-GB_Anbau_2441

GB

ATTACHING THE MACHINE

Safety 

advice: 

see Supplement 

A1, points1-8.

Hydraulic connections – Variant: Standard

1

2

1

2

3

3

2

2

075-09-17

Hydraulikleitungen beim Traktor anschließen 
Connect hydraulic lines to tractor

-   Turn p.t.o. off before connecting 

-    Put lever (ST) on the control unit into the floating position 

(0).

-   Take care that snap-lock couplers are clean. 

-   Only connect hydraulic system to the tractor when 

stopcock is closed (position A).

Lever position:
Pos.1: Operation with 2 control devices

-  The working width for the front rotary units is 

simultaneously increased or decreased.

-  Pulling on the rope (S) will alter the swath width via 

both rear rotary units

Pos. 2: Operation with 3 control devices

-  The working width for the front rotary units left and 

right is individually increased or decreased

-  The working width of the right rotary unit is increased 

or decreased using the second control device

  Pulling on the rope (S) will alter the swath width via 

both rear rotary units

-  The working width of the left rotary unit is increased 

or decreased using the third control device

Pos. 1

Pos. 2

Summary of Contents for s Series



































































Reviews: