manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 82 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 82

9.2.4  Time programs

General information about the time programs.

Note

Time programs 1 and 2 are always assigned to the respective 

heating circuits (1 and 2) and only displayed if these heating cir­

cuits are present and also turned on in the menu Configuration 

(prog.-no. 5710 and 5715).

Time program 3 can be used for heating circuit 3, for the DHW and for the 

circulation pump, depending on the setting, and is always displayed.
Time program 4 can be used for the DHW and for the circulation pump, 

depending on the setting, and is always displayed.
Time program 5 is not assigned a function and can be freely used for any 

application using an output QX.

Select (500 – 600)

Selection of weekday or day blocks. The day blocks (Mon-Sun, Mon-Fri 

and Sat-Sun) assist the adjustment. The set times are only copied to the 

individual weekdays and can be changed in the individual day settings as 

required.
The times of the individual weekdays always determine the heating pro­

gram.

Note

If a time in a group of days is changed, all 3 start/stop phases will 

be copied to the day group automatically.

To select groups of days (Mon-Sun, Mon-Fri or Sat-Sun), turn the 

control knob anti-clockwise; to select individual days (Mon, Tue, 

Wed, Thu, Fri, Sat, Sun), turn the control knob clockwise.

Heating phases (501 — 606)

Up to 3 heating phases can be set per heating circuit. These are active on 

the days selected under Select (prog.no. 500, 520, 540, 560, 600). During 

the heating phases the system heats to the set comfort setpoint. Outside 

the heating phases, the system heats to the reduced setpoint.

Note

The time programs are only activated in Automatically operating 

mode.

Copy? (515–615)

The time switching program for one day can be copied and assigned to 

another or several other days.

Note

Day blocks cannot be copied.

Default values (516–616)

Setting of the default values given in the setting table

9.2.5  Holiday programs

Select (641 - 661)

Note

The heating circuits may be set to a selectable operation level with 

the holiday programme during a certain holiday period.

8 holiday periods can be selected with this preselection.

Start of holiday (642 - 662)

Entering the holiday start.

9  Settings

82

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Summary of Contents for Paramount four

















































































































































Reviews:

No comments