manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 6 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 6

1  Safety

1.1  General safety instructions

Danger

If you smell gas:

1. Do not use a naked flame, do not smoke, do not 

operate electrical contacts or switches (doorbell, 

light, motor, lift, etc.).

2. Shut off the gas supply.

3. Open the windows.

4. Trace possible leaks and seal them immediately.

5. If the gas leak is before the gas meter, contact the 

gas supplier.

Danger

Danger to life. 

Observe the warnings affixed to the gas condensing 

boiler. Incorrect operation of the gas condensing boil­

er can lead to considerable damage.

Danger

Danger to life. 

Commissioning, settings, maintenance and cleaning 

of gas condensing boilers may only be carried out by 

a qualified installer.

Danger of electric shock

Danger to life due to improper work.

All electrical work in connection with the installation 

may only be carried out by a trained electrician.

Danger

Risk of poisoning.

Never use water from the heating system as drinking 

water. It is contaminated by deposits.

Caution

Danger of freezing!

If there is a danger of freezing do not shut down the 

heating system; continue to operate it at least in econ­

omy mode with radiator valves open. You should only 

shut down the heating system and drain the boiler, do­

mestic water storage tank and radiators if it is not pos­

sible to heat in frost mode.

Caution

Secure against unintentional switch-on!

When the heating system is empty, ensure that the 

boiler cannot be switched on unintentionally.

1  Safety

6

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Summary of Contents for Paramount four

















































































































































Reviews:

No comments