manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 43 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 43

6.4.5  Protection against contact

Danger of electric shock

Danger to life due by missing shock-proof protection.

To ensure shock-proof protection, all parts of the boiler to be 

screwed on – the casing parts in particular – must be screwed on 

correctly after work has been completed.

6.4.6  IP rating IPx4D

Tighten the cable entries to comply with the IPx4D rating and to safeguard 

the specified air-tight sealing of the air chamber, so that the grommets 

tighten around the cables.

6.4.7  Circulating pumps

The permissible current load per pump output is I

N max

 = 1A.

6.4.8  Appliance fuses

Appliance fuse in the control unit ISR:

Mains fuses: T 6.3A H 250V

6.4.9  Connecting sensors/components

Danger

Risk of electric shock! Danger to life through incorrect work!

The wiring diagram must be followed! Optional accessories must 

be fitted and connected according to the instructions provided. 

Connect to the mains. Check earthing.

Outdoor temperature sensor (included in delivery)
The outdoor temperature sensor is located in the accessory bag. For con­

nection, see the wiring diagram.

6  Installation

7658013 - 02 - 15092016

Paramount four 30 – 115 kW

43

Summary of Contents for Paramount four

















































































































































Reviews:

No comments