manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 28 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 28

5  Before installation

5.1  Regulations governing installation

Caution

Installation of the appliance must be done by a qualified engineer 

in accordance with prevailing local and national regulations.

5.2  Installation requirements

5.2.1  Corrosion protection

Caution

The combustion air must be free from corrosive elements - espe­

cially vapours containing fluorine and chlorine which are found, for 

example, in solvents and cleaning agents, propellant gases etc. 

When connecting heat generators to under-floor heating systems employ­

ing plastic pipes which are not impervious to oxygen in accordance to DIN 

4726, heat exchangers must be used for separation purposes.

Note

Prevention of damage in hot water heating systems caused by 

corrosion on the water side or scaling.

5.2.2  Supply air openings

Caution

Keep the inflow area clear.

Never block or close off ventilation apertures. The inflow area for 

combustion air must be kept clear.

Warning

Risk of damage.

The gas condensing boiler may only be installed in rooms with 

clean combustion air. Foreign matter such as pollen must never 

filter through the inlet apertures to reach the inside of the appli­

ance. The boiler must not be started up if there is heavy dust de­

velopment e.g. during construction work. There could be damage 

to the boiler.

Where the Paramount four is operated based on room ventilation, there 

must be a sufficiently large opening for combustion air available in the in­

stallation room. The operator must be informed that this opening must 

never be closed or blocked and that the connecting piece for combustion 

air on the upper side of the Paramount four must be kept free at all times.

5.2.3  Heating water requirements

Caution

Observe the heating water quality requirements!

Requirements regarding heating water quality have increased in 

recent times as system conditions have changed:

lower heat demand

use of gas condensing boilers in cascade in larger projects

increased use of buffer storage tanks in combination with solar 

thermal systems and solid fuel boilers.

The focus is always on designing systems that guarantee trouble-

free service over a long period.

Generally speaking, the quality of drinking water is adequate, but it must 

be checked whether the drinking water actually filled into the system is 

suitable when its hardness is taken into consideration (see 

water hardness 

diagram

). Where that is not the case, different steps can be taken:

5  Before installation

28

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Summary of Contents for Paramount four

















































































































































Reviews:

No comments