Potterton Paramount four Installation Manual Download Page 134

Page: 134 / 144

11 Troubleshooting

11.1 Error codes

11.1.1 Fault code table

The following is an extract from the fault code table. If other fault

codes are displayed, please inform the installer.

Fault

code

Fault description

Explanations/causes

No fault

Outside temp sensor fault

Check connection or outside temp sensor, emergency opera

tion

Boiler temperature 1 sensor fault

Check connection, inform heating specialist

(1)

Boiler temperature solid fuel sensor fault

Flow temperature 1 sensor fault

Flow temperature 2 sensor fault

Check connection, inform heating specialist

Boiler temperature solid fuel sensor fault

Return temperature 1 sensor fault

Check connection, inform heating specialist

Boiler temperature solid fuel sensor fault

Common return temp sensor fault

DHW temperature 1 sensor fault

Check connection, inform heating specialist, emergency oper
ation

DHW temperature 2 sensor fault

Check connection, inform heating specialist

Flow temperature DHW sensor fault

Drinking water circulation temperature sensor fault

Room temperature 1 sensor fault

Room temperature 2 sensor fault

Room temperature 3 sensor fault

Storage tank temp 1 (top) sensor fault

Storage tank temp 2 (bottom) sensor fault

Storage tank temp 3 (middle) sensor fault

Collector temperature 1 sensor fault

LPB short-circuit or no bus power supply

LPB address collision

Check addresses of connected control modules

BSB wire short-circuit

Check connection of the room units

BSB address collision

2 room devices have the same assignment (prog.no. 42)

BSB wireless commissioning fault

EEPROM fault: information of locking mechanism

Internal fault LMS, process sensor, replace LMS, heating spe

cialist

Expansion module 1 fault (collective fault)

Expansion module 2 fault (collective fault)

100

Two time masters (LPB)

Check time master

102

Clock time master without backup

105

Maintenance message

See maintenance code (press information button once) for de

tailed information

109

Boiler temperature monitoring

11 Troubleshooting

134

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Summary of Contents for Paramount four

















































































































































Search results

Summary of Contents for Paramount four

Reviews:

Potterton Paramount four, Installation Manual, Page: 134 / 144

Search results

Summary of Contents for Paramount four

Reviews: