manualshive.com logo in svg

Potterton Paramount four, Installation Manual, Page: 10 / 144

Share
Download
Potterton Paramount four Installation Manual Download Page 10

2  About this manual

2.1  General

This manual is intended for installers of Paramount four boilers.

2.2  Additional documentation

2.2.1  Additional documentation

Here is an overview of the further documents belonging to this heating 

system.

Tab.1

Overview table

Documentation

Contents

Intended for

Technical information

Planning documents

Description of function

Technical data/circuit diagrams

Basic equipment and accessories

Application examples

Call-for-tender texts

Planner, installer, customer

Installation manual

– Extended information

Intended use

Technical data/circuit diagram

Regulations, standards, CE

Notes for installation location

Application example, Standard application

Commissioning, operation and programming

Maintenance

Installer

User manual

Commissioning

Operation

User settings/programming

Fault table

Cleaning/maintenance

Energy-saving tips

Customer

Asset ledger

Commissioning report

Check list for commissioning

Maintenance

Installer

Abridged instructions

Operation in brief

Customer

Accessories

Installation

Operation

Installer, customer

2.3  Symbols used

2.3.1  Symbols used in the manual

This manual uses various danger levels to draw attention to special in­

structions. We do this to improve user safety, to prevent problems and to 

guarantee correct operation of the appliance.

2  About this manual

10

Paramount four 30 – 115 kW

7658013 - 02 - 15092016

Summary of Contents for Paramount four

















































































































































Reviews:

No comments