manualshive.com logo in svg

Posital Fraba KIT CONTROL BOX WITH GUI, Manual

Share
Download
Posital Fraba KIT CONTROL BOX WITH GUI Manual Download Page 3

 

Manual Kit Control Box with GUI 

Page 3

 

Version: 2020-09-10 

 

MANUAL 

KIT CONTROL BOX WITH GUI  

 

Version Date: 16.08.2020  

Version Number: 2.0  

Authors: JSC  

Reviewer: KMA, YTR

 

Valid for: 

Kit Control Box 

With software version SW V.2.0.0. 

Kit encoder with BiSS C interface (type KCD-BC0xB-1617-xxxx-xxx) 
Kit encoder with SSI interface (type KCD-S10xB-1617-xxxx-xxx) 

 

 

 

User Annotation  

Please note, that no responsibility is assumed by POSITAL for any consequences arising  from the use of 

this material. This document is not intended as an instruction manual for untrained personnel. 

 

POSITAL welcomes all readers to send their feedback about the product and this document.  

 

Contact  

 

FRABA America

 

T +1 609 750-8705  

  [email protected] 

 

FRABA Europe 

T +49 221 96213-0 

  [email protected] 

 

FRABA Asia 

T +65 6514 8880 

  [email protected] 

 

 

© FRABA B.V., All rights reserved. We do not assume responsibility for technical inaccuracies or omissions. Specifications are subject to 

change without notice.

 

 

 

 

 

Summary of Contents for KIT CONTROL BOX WITH GUI






















Reviews:

No comments

Brands by name

Popular brands

Load more brands