CONGRATULATIONS on your purchase
of a POSI LOCK gear and bearing puller.
Your POSI LOCK is engineered to
perform like no other puller can.
INSTRUCTIONS
Before each usage clean and lubricate the center
bolt threads.
Use a good grade of high pressure
grease or graphite based lubricant.
Always use hand tools on gear pullers. Avoid the
use of power tools (impact wrenches, etc.) as they
can produce an undetermined amount of torque
and may exceed the stated maximum torque. This
will prolong the life of your threads.
To operate, grasp the puller with one hand and
turn the T-handle with the other. Continue
turning until the jaw opening is set to fit over the
component being pulled. Then turn the T-handle
in a clockwise direction to lock the jaws firmly onto
the component. (When using three jaw models,
make sure the center bolt is aligned with the center
of the shaft before securing the handle.) Proceed
to tighten the center bolt to pull the component. If
necessary, the center bolt can be hit with a hammer
to aid in loosening the component.
NOTE:
When only the inner bearing race is
remaining on the shaft, clean the shaft first with
emery cloth. Next attach the jaws in the ball
groove. Tighten the T-handle as tight as possible
with a wrench to secure the jaws in the groove.
Tighten the center bolt to remove inner bearing
race. Should the jaws appear to be coming out of
the groove, loosen the center bolt and retighten the
T-handle. This may be necessary when the puller
is new, to get the cage to properly seat on the jaws.
Once seated, tightening the cage firmly the first
time should be sufficient.
CAUTION: Distortion of jaw head tube may
occur if bolt nut is continually forced against
jaw head tube. Bolt extensions are available
to eliminate this situation. Use tip protector
provided.
POSI LOCK®
Gear and Bearing Pullers
INSTRUCTION & PARTS SHEET FOR ALL MODELS
IMPORTANT: READ CAREFULLY!!
MODELS, PART NUMBERS & SPECIFICATIONS
MO
D
EL
10
2
1 Ton
3 Jaw
Reach: 2.25”
Spread: .25” - 3.25”
Weight: .7 lbs
1) Cage Assembly
10253
2) 2.25” Jaw - 3 Used
10254
3) Jaw Head Assembly 10255
4) Slotted Spring Pin
10256
5) T-Handle
10257
6) Center Bolt
10258
7) Snap Ring
10259
MO
D
EL
10
4
5 Ton
3 Jaw
Reach: 4”
Spread: 0.5” - 5”
Weight: 4 lbs
Max. Torque:
40 ft./lb.
1) Cage Assembly
10453
2) 4” Jaw - 3 Used
10454
3) Jaw Head Assembly 10455
4) Pin Assembly
10456
5) T-Handle
10457
6) Center Bolt
10458
7) Snap Ring
10459
8) Tip Protector
P4
MO
D
EL
10
6
10 Ton
3 Jaw
Reach: 6”
Spread: .5” - 7”
Weight: 8 lbs
Max. Torque:
130 ft./lb.
1) Cage Assembly
10653
2) 6” Jaw - 3 Used
10654
3) Jaw Head Assembly 10655
4) Pin Assembly
10656
5) T-Handle
10657
6) Center Bolt
10658
7) Snap Ring
10659
8) Tip Protector
P6
MO
D
EL
10
8
17 Ton
3 Jaw
Reach: 8”
Spread: .75” - 12”
Weight: 14 lbs
Max. Torque:
220 ft./lb.
1) Cage Assembly
10853
2) 8” Jaw - 3 Used
10854
3) Jaw Head Assembly 10855
4) Pin Assembly
10856
5) T-Handle
10857
6) Center Bolt
10858
7) Snap Ring
11059
8) Tip Protector
P10
MO
D
EL
11
0
20 Ton
3 Jaw
Reach: 9.67”
Spread: 1” - 15”
Weight: 16 lbs
Max. Torque:
275 ft./lb.
1) Cage Assembly
11053
2) 10” Jaw - 3 Used
11054
3) Jaw Head Assembly 11055
4) Pin Assembly
11056
5) T-Handle
11057
6) Center Bolt
11058
7) Snap Ring
11059
8) Tip Protector
P10
MO
D
EL
11
3
30 Ton
3 Jaw
Reach: 12”
Spread: 2.5” - 18”
Weight: 44 lbs
Max. Torque:
600 ft./lb.
1) Cage Assembly
11353
2) 12” Jaw - 3 Used
11354
3) Jaw Head Assembly
11355
4) Pin Assembly
11356
5) T-Handle
11357
6) Center Bolt
11358
7) Snap Ring
11359
8) Tip Protector
P13/16
MO
D
EL
11
6
40 Ton
3 Jaw
Reach: 14”
Spread: 3” - 25”
Weight: 68 lbs
Max. Torque:
850 ft./lb.
1) Cage Assembly
11653
2) 14” Jaw - 3 Used
11654
3) Jaw Head Assembly
11655
4) Pin Assembly
11356
5) T-Handle
11657
6) Center Bolt
11658
7) Snap Ring
11659
8) Tip Protector
P13/16
2 Jaw Pullers
3 Jaw Pullers
MO
D
EL
10
3
2 Ton
3 Jaw
Reach: 3”
Spread: .25” - 4.5”
Weight: 1.3 lbs
1) Cage Assembly
10353
2) 3” Jaw - 3 Used
10354
3) Jaw Head Assembly 10355
4) Slotted Spring Pin
10356
5) T-Handle
10357
6) Center Bolt
10358
7) Snap Ring
10359
MO
D
EL
202
1 Ton
2 Jaw
Reach: 2.25”
Spread: .25” - 3.25”
Weight: .6 lbs
1) Cage Assembly
20253
2) 2.25” Jaw - 2 Used
10254
3) Jaw Head Assembly 20255
4) Slotted Spring Pin
10256
5) T-Handle
10257
6) Center Bolt
10258
7) Snap Ring
10259
MO
D
EL
20
4
2 Ton
2 Jaw
Reach: 4”
Spread: 0.5” - 5”
Weight: 4 lbs
Max. Torque:
20 ft./lb.
1) Cage Assembly
20453
2) 4” Jaw - 2 Used
10454
3) Jaw Head Assembly 20455
4) Pin Assembly
10456
5) T-Handle
10457
6) Center Bolt
10458
7) Snap Ring
10459
8) Tip Protector
P4
MO
D
EL
206
6 Ton
2 Jaw
Reach: 6”
Spread: .5” - 7”
Weight: 7 lbs
Max. Torque:
75 ft./lb.
1) Cage Assembly
20653
2) 6” Jaw - 2 Used
10654
3) Jaw Head Assembly 20655
4) Pin Assembly
10656
5) T-Handle
10657
6) Center Bolt
10658
7) Snap Ring
10659
8) Tip Protector
P6
MO
D
EL
208
12 Ton
2 Jaw
Reach: 8”
Spread: .75” - 12”
Weight: 12 lbs
Max. Torque:
150 ft./lb.
1) Cage Assembly
20853
2) 8” Jaw - 2 Used
10854
3) Jaw Head Assembly 20855
4) Pin Assembly
11056
5) T-Handle
11057
6) Center Bolt
10858
7) Snap Ring
11059
8) Tip Protector
P10
MO
D
EL
210
14 Ton
2 Jaw
Reach: 9.67”
Spread: 1” - 15”
Weight: 13 lbs
Max. Torque:
175 ft./lb.
1) Cage Assembly
21053
2) 10” Jaw - 2 Used
11054
3) Jaw Head Assembly 21055
4) Pin Assembly
11056
5) T-Handle
11057
6) Center Bolt
11058
7) Snap Ring
11059
8) Tip Protector
P10
MO
D
EL
213
25 Ton
2 Jaw
Reach: 12”
Spread: 2.5” - 18”
Weight: 38 lbs
Max. Torque:
475 ft./lb.
1) Cage Assembly
21353
2) 12” Jaw - 2 Used
11354
3) Jaw Head Assembly 21355
4) Pin Assembly
11356
5) T-Handle
11357
6) Center Bolt
11358
7) Snap Ring
11359
8) Tip Protector
P13/16
MO
D
EL
21
6
35 Ton
2 Jaw
Reach: 14”
Spread: 3” - 25”
Weight: 57 lbs
Max. Torque:
800 ft./lb.
1) Cage Assembly
21653
2) 14” Jaw - 2 Used
11654
3) Jaw Head Assembly 21655
4) Pin Assembly
11356
5) T-Handle
11657
6) Center Bolt
11658
7) Snap Ring
11659
8) Tip Protector
P13/16
MO
D
EL
20
3
2 Ton
2 Jaw
Reach: 3”
Spread: .25” - 4.25”
Weight: 1.2 lbs
1) Cage Assembly
20353
2) 3” Jaw - 2 Used
10354
3) Jaw Head Assembly 20355
4) Slotted Spring Pin
10356
5) T-Handle
10357
6) Center Bolt
10358
7) Snap Ring
10359
RIGHT
WRONG
SPECIAL NOTE:
If bar must be inserted between jaws to keep
puller from turning, be sure bar is wedged
between the jaws and
NOT THE THREADED
SHAFT.
Wedging between the jaw and the shaft
will cause stripping of the threads.
