Posch M6140 Operating Instructions Manual Download Page 22 | Manualshive

Page: 22 / 32

background image

Maintenance

Before carrying out any maintenance on the machine, the drive unit MUST be switched off!
Disconnect the machine from the mains.

Work on electrical equipment must only be carried out by qualified electricians.
Never work without the protective guards in place.
Only use original - POSCH - spare parts.

Tool guide

Apply grease with a brush.
The tool guide must always be well greased.

Recommended lubricating greases:

Manufacturer

Type

Genol

Multi-purpose grease

Fuchs

Multi-purpose grease 5028

Oil changing

Old oil must be disposed of in an environment-friendly manner. Find out about the

environmental regulations in your country.

Changing the hydraulic oil

The first oil change should be carried out after 500 operating hours, further oil changes

should then be carried out every 1000 operating hours or yearly.

9

9.1

9.2

9.2.1

Maintenance

22

«
...
20
21
22
23
24
...
»

Summary of Contents for M6140

































Reviews:

No comments

Related manuals for M6140

Brand: Range Road Pages: 18

Brand: Champion Power Equipment Pages: 32

Brand: Vito Agro Pages: 48

Brand: Hud-son Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands