Portwell ROBO-8914VG2AR Page 42 User Manual Download | Manualshive

Page: 42 / 80

background image

BIOS Setup Information

ROBO-8914VG2AR User’s Manual

4-6

IDE Configuration

The IDE Configuration the IDE devices, such as hard disk drive or CD-ROM drive. It
uses a separate sub menu to configure each hard disk drive (Master and Slave).

Mirrored IDER Configuration

The choice: Disabled, Enabled.

SATA#1 Configuration

The choice: Compatible, Enhanced.

SATA#2 Configuration

The choice: Disabled, Enhanced

Configure SATA#1 as

This setting specifies the function of the on-chip SATA#1 controller.

The choice: IDE, RAID, AHCI.

«
...
40
41
42
43
44
...
»

Summary of Contents for ROBO-8914VG2AR

















































































Reviews:

No comments

Related manuals for ROBO-8914VG2AR

Brand: Lantronix Pages: 8

Brand: Xilinx Pages: 14

ASC Bridge Board

Brand: Lattice Semiconductor Pages: 25

Brand: AOpen Pages: 8

Brand: IEI Technology Pages: 8

Brand: Tadao Pages: 3

Brand: QDI Pages: 19

Brand: Texas Instruments Pages: 31

Brand: TYAN Pages: 81

Brand: TYAN Pages: 64

Brand: DFI Pages: 76

Brand: DFI Pages: 149

Brand: ASROCK Pages: 5

Brand: JETWAY Pages: 42

Brand: IDT Pages: 11

Brand: IDT Pages: 20

Demo Circuit 1592A

Brand: Linear Technology Pages: 9

Brand: Linear Technology Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands