manualshive.com logo in svg

Pontiac 2009 Solstice, Owner'S Manual, Page: 278 / 354

Share
Download
Pontiac 2009 Solstice Owner'S Manual Download Page 278

9. Inflate the tire to the recommended inflation

pressure using the pressure gage (E). The
recommended inflation pressure can be found
on the Tire and Loading Information label. See
Inflation - Tire Pressure on page 5-53.

The pressure gage (E) may read higher than the
actual tire pressure while the compressor is on. Turn
the compressor off to get an accurate pressure
reading. The compressor may be turned on/off until
the correct pressure is reached.

Notice: If the recommended pressure cannot be
reached after approximately 25 minutes, the vehicle
should not be driven farther. The tire is too
severely damaged and the tire sealant and
compressor kit cannot inflate the tire. Remove the
power plug from the accessory power outlet
and unscrew the inflating hose from the tire valve.
See Roadside Assistance Program on page 7-6.

10. Press the on/off button (D) to turn the tire sealant

and compressor kit off.

The tire is not sealed and will continue to
leak air until the vehicle is driven and the
sealant is distributed in the tire, therefore,
Steps 11 through 17 must be done immediately
after Step 10.

Be careful while handling the tire sealant and
compressor kit as it could be warm after usage.

11. Unplug the power plug (C) from the accessory

power outlet in the vehicle.

12. Turn the sealant/air hose (F) counterclockwise to

remove it from the tire valve stem.

13. Replace the tire valve stem cap.

14. Replace the sealant/air hose (F), and the power

plug (C) back in their original location.

15. If the flat tire was able

to inflate to the
recommended inflation
pressure, remove
the maximum speed
label from the sealant
canister (B) and
place it in a highly
visible location.

The label is a reminder not to exceed 55 mph
(90 km/h) until the damaged tire is repaired
or replaced.

16. Return the equipment to its original storage location

in the vehicle.

17. Immediately drive the vehicle 5 miles (8 km) to

distribute the sealant in the tire.

5-76

Summary of Contents for 2009 Solstice



































































































































































































































































































































































Reviews:

No comments