Pontiac 2009 Solstice Owner'S Manual Download Page 247

Page: 247 / 354

License Plate Lamp

To replace the license plate lamp bulb:

1. Remove the license plate assembly by turning the

two screws counterclockwise.

2. Turn and pull the license plate lamp forward

through the fascia opening.

3. Turn the bulb socket counterclockwise and pull the

bulb straight out of the socket.

4. Push the new bulb in and turn it clockwise to install.

5. Replace the license plate lamp by pushing it

through the fascia opening.

6. Turn the two screws that hold the license plate

lamp clockwise to reinstall.

Replacement Bulbs

Exterior Lamp

Bulb Number

Back-Up Lamps

3047

Fog Lamp

898*

Front Parking/Turn Signal Lamp

3757NAK

Front Sidemarker Lamp

194

Headlamps, High/Low-Beam/
Daytime Running Lights

H13

License Plate Lamp

168

Stoplamp, Taillamp and Turn
Signal Lamp

3157K

* Uplevel Model

For replacement bulbs not listed here, contact your
dealer/retailer.

5-45

Summary of Contents for 2009 Solstice



































































































































































































































































































































































Search results

Summary of Contents for 2009 Solstice

Reviews:

Pontiac 2009 Solstice, Owner'S Manual, Page: 247 / 354

Search results

Summary of Contents for 2009 Solstice

Reviews: