Home
/
Pontiac
/
2009 Solstice
/
Owner'S Manual

Pontiac 2009 Solstice, Owner'S Manual, Page: 149 / 354

Share

Page: 149 / 354

Pontiac 2009 Solstice Owner'S Manual Download Page 149

4. To go to the previous or to the next XM station

within the selected category, do one of the
following:

•

Turn

f

.

•

Press the softkeys below the right or left arrows
on the radio display.

•

Press

©

SEEK or

¨

SEEK.

5. To exit the category search mode, press the FAV

button or BAND button to display the favorites again.

Undesired XM categories can be removed through the
setup menu. To remove an undesired category:

1. Press MENU to display the radio setup menu.

2. Press the softkey below the XM CAT tab.

3. Turn

f

to display the category to be removed.

4. Press the softkey below the Remove tab until the

category name along with the word Removed
displays.

5. Repeat the steps to remove additional categories.

Removed categories can be restored by pressing
the softkey under the Add tab when a removed category
displays or by pressing the softkey below the Restore
All tab.

Categories cannot be removed or added while the
vehicle is moving faster than 5 mph (8 km/h).

Radio Messages

Calibration Error: Displays if the radio is no longer
calibrated properly for the vehicle. The vehicle must be
returned to your dealer/retailer for service.

Loc or Locked: Displays when the THEFTLOCK

®

system has activated. Take the vehicle to your
dealer/retailer for service.

If any error occurs repeatedly or if an error cannot be
corrected, contact your dealer/retailer.

XM Satellite Radio Service

XM is a satellite radio service that is based in the
48 contiguous United States and 10 Canadian
provinces. XM Satellite Radio has a wide variety of
programming and commercial-free music,
coast-to-coast, and in digital-quality sound. During your
trial or when you subscribe, you will get unlimited
access to XM Radio Online for when you are not in the
vehicle. A service fee is required to receive the XM
service. For more information, contact XM at
xmradio.com or call 1-800-929-2100 in the U.S. and
xmradio.ca or call 1-877-438-9677 in Canada.

Radio Messages for XM Only

See XM Radio Messages on page 3-67 for more
information.

3-55

«
...
147
148
149
150
151
...
»

Summary of Contents for 2009 Solstice



































































































































































































































































































































































Reviews:

No comments