manualshive.com logo in svg

Pontiac 2009 Solstice, Owner'S Manual, Page: 131 / 354

Share
Download
Pontiac 2009 Solstice Owner'S Manual Download Page 131

BOOST (Turbo Only)

If your vehicle has this feature, press the information
button until BOOST displays. This mode shows a
graphic that indicates the amount of boost the engine is
receiving in either pounds per square inch (psi) or
kilopascals (kPa).

DIC Warnings and Messages

These messages appear if there is a problem detected
in one of your vehicle’s systems.

A message clears when the vehicle’s condition is no
longer present. To acknowledge a message and clear it
from the display, press and hold any of the DIC
buttons. If the condition is still present, the warning
message comes back on the next time the vehicle is
turned off and back on. With most messages, a warning
chime sounds when the message displays. Your
vehicle may have other warning messages.

AUTO (Automatic) LIGHTS OFF

This message displays if the automatic headlamp
system is disabled with the headlamp switch.

AUTO (Automatic) LIGHTS ON

This message displays if the automatic headlamp
system is enabled with the headlamp switch.

BRAKE FLUID

This message displays, while the ignition is on, when
the brake fluid level is low. The brake system warning
light on the instrument panel cluster also comes on. See
Brake System Warning Light on page 3-25 for more
information. Have the brake system serviced by
your dealer/retailer as soon as possible.

CHANGE OIL SOON

This message displays when the life of the engine oil
has expired and it should be changed.

When this message is acknowledged and cleared from
the display, the engine oil life system must still be
reset separately. See Engine Oil Life System on
page 5-19 and Scheduled Maintenance on page 6-4 for
more information.

CHECK GAS CAP

This message displays if the fuel cap has not been fully
tightened. Recheck the fuel cap to make sure that it
is on properly. A few driving trips with the cap properly
installed should turn the message off.

CHECK TIRE PRESS (Pressure)

On vehicles with the Tire Pressure Monitor System
(TPMS), this message displays when the pressure in
one or more of the vehicle’s tires needs to be checked. If
a tire pressure message appears on the DIC, stop as

3-37

Summary of Contents for 2009 Solstice



































































































































































































































































































































































Reviews:

No comments