manualshive.com logo in svg

Pontiac 2001 Aztek, Owner'S Manual, Page: 208 / 433

Share
Download
Pontiac 2001 Aztek Owner'S Manual Download Page 208

3-8

Air Conditioning

On very hot days, your vehicle will cool down more
quickly and economically if you open the windows long
enough to let hot, inside air escape. For all settings,
adjust the temperature knob and fan speed as desired.

To get maximum cooling or a quick cool

-

down on very

hot days, press the A/C and RECIRCULATION buttons
(the lights will glow) and move the temperature knob
down (toward the blue area). Then, adjust the mode
knob to direct the air to the desired location. This setting
should not be used for long periods of time because the
air may become too cold and dry.

Push the A/C button again (the light will go off) to turn
off the air conditioning.

When the air conditioner compressor is on, you may
sometimes notice slight changes in your vehicle’s engine
performance and power. This is normal. The system is
designed to help fuel economy while it maintains the
desired cooling level.

The air conditioner removes moisture from the air, so
you may sometimes notice water dripping from under
your vehicle’s engine compartment when it is idling or
after it has been turned off. This is normal.

Heating

Move the temperature knob up (toward the red area) to
warm the air.

In the LOWER mode, outside air will be brought in and
sent through the floor outlets. The heater works best if
you keep your windows closed while using it.

The BI

-

LEVEL setting is designed for use on sunny

days when the air is only moderately warm or cool. 
On days like these, the sun may adequately warm your
upper body, but your lower body may not be warm
enough. For the best results, move the temperature knob
to the middle position, and then adjust it for comfort.

Your vehicle has a computer controlled transaxle
designed to warm up the engine faster when the outside
temperature is 35

_F (2_C) or colder. You may notice

that the transaxle will shift at a higher vehicle speed
until the engine is warmed up. This is a normal
condition designed to provide heat to the passenger
compartment and defrost the windows more quickly.

If you have the optional engine coolant heater and use it
during cold weather, 0

_F (

-

18

_C) or lower, your 

heating system will provide heat more quickly because
the engine coolant is already warmed. See “Engine
Coolant Heater” in the Index.

Summary of Contents for 2001 Aztek


















































































































































































































































































































































































































































Reviews:

No comments