manualshive.com logo in svg

Pontiac 2001 Aztek, Owner'S Manual, Page: 157 / 433

Share
Download
Pontiac 2001 Aztek Owner'S Manual Download Page 157

2-73

Accessory Power Outlets

Certain power accessory plugs may not be compatible to
the power accessory outlet and could result in blown
vehicle or adapter fuses. If you experience a problem,
see your dealer for additional information on the power
accessory plugs.

Power outlets can be used to plug in electrical
equipment such as a cellular telephone, CB radio, etc.
Follow the proper installation instructions that are
included with any electrical equipment you install.

There are two front power outlets when the optional
cigarette lighter is not in use. One is located on the
center console switchbank. The other is located on the
floor console above the vents. Pull the cover down to
use a power outlet. When not in use, replace the cover.

There are two rear power outlets. One is located in the
rear of the floor console below the vents. The other is
located in the rear of the vehicle on the driver’s side.
Pull the cover down to use the power outlet.

When not in use, always cover the accessory power
outlets with the protective cap.

NOTICE:

When using the accessory power outlets:
D Maximum load of any electrical equipment

should not exceed 20 amps.

D Be sure to turn off any electrical equipment

when not in use. Leaving electrical equipment
on for extended periods can drain your battery.

Summary of Contents for 2001 Aztek


















































































































































































































































































































































































































































Reviews:

No comments