manualshive.com logo in svg

PolyScience MX-CA11B, Operator'S Manual, Page: 4 / 27

Share
Download
PolyScience MX-CA11B Operator'S Manual Download Page 4

 

110-511 PSC/EN 

3 

General Information 

General Safety Information 

When installed, operated, and maintained according to the directions in this manual and common safety 
procedures, your MX Immersion Circulator should provide safe and reliable liquid heating. Please ensure 
that all individuals involved in the installation, operation, or maintenance of this unit read this manual 
thoroughly prior to working with the unit.  

 

This symbol alerts you to a wide range of potential dangers. 

 

 

This symbol advises danger from electricity or electric shock. 

 

 

This symbol indicates that a hot surface may be present. 

 

This symbol marks information that is particularly important. 

 

 

This symbol indicates alternating current.

 

 

 

/

 

 

These symbols on the Power Switch / Circuit Breaker indicate that they place the main power supply 
ON / OFF.

 

 

 

This symbol on the Power Key indicates that it places the unit in a standby mode. It DOES NOT fully 
disconnect the unit from the power supply.

 

 

 

This symbol indicates a protective conductor terminal.

 

 

Read all instructions pertaining to safety, set-up, and operation.  

Proper operation is the user’s responsibility. 

[email protected]

www.

GlobalScientificSupply

.com

GLOBAL SCIENTIFIC SUPPLY

The Laboratory Supply Company!

Summary of Contents for MX-CA11B




























Reviews:

No comments