manualshive.com logo in svg

Polycom ViewStation FX, User Manual

The Polycom ViewStation FX is a high-quality video conferencing solution that enables seamless communication. Get started swiftly with the Quick Start manual, available for free download at manualshive.com. Gain easy access to insightful instructions and optimize your experience with this exceptional product.

Share
Download
background image

Chapter 5

System Information and Diagnostics

ViewStation FX/VS 4000 User’s Guide

154

www.polycom.com

Because data throughput has priority over video throughput, video 
bandwidth may be restricted to support data requirements.

Pass-Thru Mode is a proprietary feature that is only supported when 
both endpoints are either ViewStation FX or VS4000 stations. The 
RS-232 port only supports data Pass-Thru in H.320 mode (ISDN or 
V.35). Data Pass-Thru in an H.323 (IP) video call or multi-point call 
is not supported, as alternative file transfer methods such as ftp or 
Telnet are widely available.

Note

When in Pass-Thru Mode, both local and remote stations 
need to be set to the same data rate.

Pass-Thru Mode to Control Mode

—If the near site is set to 

Pass-Thru Mode, but the far site is set to Control Mode, then the 
device connected to the near site RS-232 port can be used to control 
the far site ViewStation FX or VS4000, using the far site’s Command 
Line Interface.

Hardware Information 

The Hardware Information screen contains information about the 
hardware components that make up your ViewStation FX or 
VS4000.

Figure 5-15.  

Hardware Information Screen

On this screen you can view information about the ViewStation FX 
or VS4000 and the protocols it uses to send the video in your calls, 
and the version of your microphone pod.

Summary of Contents for ViewStation FX





























































































































































































































Reviews:

No comments

Related manuals for ViewStation FX

Bang & Olufsen BeoSound 5 User Manual preview
BeoSound 5
Brand: Bang & Olufsen Pages: 20
Bang & Olufsen BeoSound 5 Manual preview
BeoSound 5
Brand: Bang & Olufsen Pages: 24
Bang & Olufsen BeoSound Ouverture User Manual preview
BeoSound Ouverture
Brand: Bang & Olufsen Pages: 44
PACH & COMPANY AeGIS 7000 Series Quick Start Manual preview
AeGIS 7000 Series
Brand: PACH & COMPANY Pages: 2
Pilz PNOZ m ES CC-Link Operating Manual preview
PNOZ m ES CC-Link
Brand: Pilz Pages: 24
SOUNDMASTER NR995 Manual preview
NR995
Brand: SOUNDMASTER Pages: 110
Steren BOC-2132 Manual preview
BOC-2132
Brand: Steren Pages: 26
AT&T MERLIN LEGEND Release 2.0 Analog Multiline Telephone System Programming Manual preview
MERLIN LEGEND Release 2.0 Analog Multiline Telephone
Brand: AT&T Pages: 794
Hyundai MSR 568 D3 User Manual preview
MSR 568 D3
Brand: Hyundai Pages: 88
BFT GIOTTO 30-50 BT Installation And User Manual preview
GIOTTO 30-50 BT
Brand: BFT Pages: 21
Power Dynamics PA203 Instruction Manual preview
PA203
Brand: Power Dynamics Pages: 16
Dormakaba SVP-S 4 DCW Series Mounting Instructions preview
SVP-S 4 DCW Series
Brand: Dormakaba Pages: 5
AAD PL-100 Owner'S Information preview
PL-100
Brand: AAD Pages: 8
Pioneer KEX-M9537ZT-02/UC Service Manual preview
KEX-M9537ZT-02/UC
Brand: Pioneer Pages: 8
Pioneer KEH-P4020 - Radio / Cassette Player Installation Manual preview
KEH-P4020 - Radio / Cassette Player
Brand: Pioneer Pages: 6
Pioneer KEH-P4010R Installation Manual preview
KEH-P4010R
Brand: Pioneer Pages: 6
Pioneer KEH-P2035 Installation Manual preview
KEH-P2035
Brand: Pioneer Pages: 6
Pioneer KEH-1940 Installation Manual preview
KEH-1940
Brand: Pioneer Pages: 6

Brands by name

Popular brands

Load more brands