iPower 600 Series Collaboration System Easy Install
Side 1
Copyright © 2002: Polycom, Inc.–Printed in U.S.A.
Polycom and the Polycom logo are registered trademarks of Polycom, Inc.
PictureTel and the PictureTel logo are registered trademarks of PictureTel Corporation. PowerMic, ImageShare,
and iPower are trademarks of PictureTel Corporation. Velcro is a registered trademark of Velcro USA, Inc.
Edition: 800-1276-01/C
*P800-1276-01*
Get Ready to Install Your System:
Make Sure the Network Is Ready
Before you begin installing your iPower
™
600 Series system, you should make sure
that the network is ready.
The document
Preparing Your Network for Collaboration
contains worksheets that will
help you get the network ready. For example, for ISDN networks, the worksheets list
requirements for the system, such as the ISDN BRI dialect, the Network Type, and so
on. You can find the
Preparing Your Network for Collaboration
document at the
Polycom web site, http://www.polycom.com.
If you’ve already followed the steps in the
Preparing Your Network for Collaboration
document or the network administrator has already taken care of the network
preparation for you, you can continue with the installation.
Unpack
When you unpack all the cartons, this is what you should have:
Documentation and Remote Control
Power
Num
Cap
Scroll
Camera and Microphone Module
Cables
Audio output cable
for main monitor
S-video cable
for second monitor
[E185633 Style 2464/80
C 300V]
ISDN cables
(one cable for Single BRI;
four cables for Quad BRI)
[E166211 Style 20251/60
C 150V]
Computer Unit
Note: The serial number is printed on the back
of the computer unit. Record the number here
in case you need it for future reference.
Serial Number: ______________________
Keyboard
Keyboard Receiver
Power cable
WARNING: You must connect the system to
the power cable that is packed in the box.
Connecting it to any other kind of power cable
will cause a risk of fire or electric shock.
PIP
ZOOM
VOLUME
MUTE
AUTO
CONTENT
PEOPLE
SET
CANCEL
PRESET
7 PQRS
8 TUV
9 WXYZ
4 GHI
5 JKL
6 MNO
2 ABC
3 DEF
*
0
#
CALL/ANSWER
HANG UP
HELP
ON/STANDBY
OPTIONS
1
Note: The S-video cable and ISDN cables included with your PictureTel 600 Series
system have been approved for use with this system under file number E120890.
Install Your System:
Attach Your System to the Top of the Monitor
You can attach the Camera and Microphone module to the computer unit and place
the system on top of a monitor. Or, you can keep the Camera and Microphone module
and the computer unit separate and mount the Camera and Microphone module on a
flat panel display or on a wall. If you keep them separate, you will need to use the
optional interconnect cable.
Follow Steps 1 through 5 only if you’re installing your system on top of a monitor.
1. Slide the back of the Camera and Microphone module onto the front of the
computer unit. You may have to push down gently on the back of the Camera and
Microphone module to make sure it fits together securely with the computer unit.
2. Locate the plastic bag containing the three screws. Insert the screws into the
holes under the computer unit, and tighten the screws using the edge of a coin.
Caution:
Do
not
flip your system over to attach the screws. Doing so may harm
the camera. Instead, slide the system slightly over the edge of your table or desk,
and insert and tighten the screws from underneath.
3. Remove the paper backing from the Velcro
®
pieces at the bottom of both the
Camera and Microphone module and the computer unit.
4. Center the system over the top of the monitor, and then stick the system onto the
monitor. Firmly press down on the system to make sure it’s attached securely.
5. Flip the microphone into the upright position until it clicks into place.
Set Up the Remote Control and Keyboard
1. Insert the four batteries into the battery compartment in the back of the remote
control.
For the remote control to work properly, make sure that the infrared path between
the remote control and the receiver at the base of the Camera and Microphone
module is not blocked.
2. Insert the eight batteries into the battery compartment in the back of the keyboard.
To open the battery cover on the keyboard, apply pressure to both sides of the
cover.
For the keyboard to work properly, make sure that the infrared path between the
keyboard and the keyboard receiver is not blocked.
Connect the Cables
See Side 2 of this poster for complete information about how to connect the cables
and any optional equipment to your iPower 600 Series system.
After You Install Your System:
Power On the System
Now that you’ve set up the hardware and connected the cables (see Side 2 of this
poster), you’re ready to start up the system:
1. Push the power button on. You’ll find the power button on the side of the
computer unit.
The LED on the front of the system lights up.
2. Follow the Setup Wizard instructions.
Congratulations! You’re done installing your iPower 600 Series system!
Get More Information
If you’d like more information before you start using your system, here’s where to look:
In addition to the
iPower Documentation
CD, most of these documents are available
at the Polycom documentation web site at http://www.polycom.com.
You can also access the
Getting Started Guide
in .doc format from the Start menu at
Programs>iPower>Getting Started Guide.
For information on:
Look at the:
Installation or hardware
troubleshooting
iPower 600 Series Collaboration System
Administrator’s Guide
, available on the
iPower
Documentation
CD
Collaboration Help, available from the Options menu
How to connect optional
equipment, such as a
different camera or a
cart
Documentation that came with the optional equipment
Basic system
functionality, such as
making a call, pointing
the camera, changing
the volume, and so on
iPower Collaboration System Quick Tips Sheet
,
available on the
iPower Documentation
CD
iPower Collaboration System Getting Started Guide
,
available on the
iPower Documentation
CD
Collaboration Help, available from the Options menu
What AdminTools is and
how you or the system
administrator can use it
to fine-tune the system
AdminTools Help
iPower 600 Series Collaboration System
Administrator’s Guide
, available on the
iPower
Documentation
CD
How to contact Polycom
Technical Support
Polycom support web site at
http://www.polycom.com
