manualshive.com logo in svg

Poldent Endostar Provider, Instructions For Use Manual, Page: 33 / 48

Share
Download
Poldent Endostar Provider Instructions For Use Manual Download Page 33

32

2

5

1

3

4

a)

b)

Instructions for Use  2019-03-20

(1) Replacement Parts

•  Use only the battery designed for the device. Other types could cause overheating.
•  Do not use a battery if it is leaky, deformed, discolored or if its label is peeled off. It might overheat.

* Replace the parts as necessary depending on degree of wear and length of use.
* Order parts from Poldent Co. Ltd.

Replace the battery when it starts to loose power relatively quickly after being fully charged. 
The battery will last for approximately 1 year under normal circumstances and use.

Replacing the Battery

Replacement Parts, 

Transport and Storage Environments

Connector

Battery Cover

Screw

Connect the battery cord and then slide the battery along the bot-
tom.

Replace the cover and its screw. 

Turn power off. Remove the screw and slide the battery cover off.

a)  Remove an old cushion.
b)  Peel off the paper shield from the sticky side of the cushion and 

stick it to the bottom of the battery space.

Take out the old battery and disconnect it. 

Be careful not to pinch the battery cord when replacing the cover.
Do not tighten the cover screw too much; this could strip the threads.

Do not leave the power on when disconnecting the battery.

Dispose of old lithium ion batteries in an environmentally safe way and in 
strict accordance with local regulations.

A cushion must be pasted on to fill a gap between the battery and the mo-
tor handpiece.

Summary of Contents for Endostar Provider

















































Reviews:

No comments