Polaris Sportsman 9922452 Page 126 Owner'S Manual Download

Page: 126 / 148

122

TROUBLESHOOTING

Engine Doesn't Turn Over

Engine Turns Over, Fails to Start

Engine Backfires

Possible Cause

Solution

Low battery voltage

Recharge the battery to 12.8 VDC

Loose battery connections

Check all connections and tighten

Loose solenoid connections

Check all connections and tighten

Possible Cause

Solution

Out of fuel

Refuel, cycle key to ON position three

times for 5 seconds each, then start

Clogged fuel filter

See your dealer

Water is present in fuel

Drain the fuel system and refuel

Old or non-recommended fuel

Replace with fresh recommended fuel

Fouled or defective spark plugs

Inspect plugs and replace if necessary

No spark to spark plug

Inspect plugs, verify stop switch is on

Water or fuel in crankcase

Immediately see your Polaris dealer

Low battery voltage

Recharge the battery to 12.8 VDC

Mechanical failure

See your dealer

Possible Cause

Solution

Weak spark from spark plug

Inspect, clean and/or replace spark plugs

Incorrect spark plug gap or heat range

Set gap to specs or replace plugs

Old or non-recommended fuel

Replace with fresh recommended fuel

Incorrectly installed spark plug wires

See your dealer

Incorrect ignition timing

See your dealer

Mechanical failure

See your dealer

Loose ignition connections

Check all connections and tighten

Water present in fuel

Replace with fresh recommended fuel

Summary of Contents for Sportsman 9922452





















































































































































Search results

Summary of Contents for Sportsman 9922452

Reviews:

Related manuals for Sportsman 9922452

Brands by name

Popular brands

Polaris Sportsman 9922452, Owner'S Manual

Search results

Summary of Contents for Sportsman 9922452

Reviews:

Related manuals for Sportsman 9922452

Brands by name

Popular brands