Polaris Sportsman 9920629 Owner'S Manual Download Page 19

Page: 19 / 143

SAFETY

Operator Safety

• Always travel slowly and use extra caution when operating on unfa-

miliar terrain. Be alert to changing terrain conditions.

• Never operate on excessively rough, slippery, or loose terrain.
• Always follow proper turning procedures as described in this manual.

Practice turning at low speeds before attempting to turn at faster

speeds. Do not turn at excessive speeds.

• Always have the ATV inspected by an authorized Polaris dealer if it's

been involved in an accident.

• Never operate on hills too steep for the ATV or for your abilities.

Practice on smaller hills before attempting larger hills.

• Always follow proper procedures for climbing hills. Check the terrain

carefully before ascending a hill. Never climb hills with excessively

slippery or loose surfaces. Shift your weight uphill. Never open the

throttle suddenly or make sudden gear changes. Never go over the top

of a hill at high speed.

• Always follow proper procedures for going downhill and for braking

on hills. Check the terrain carefully before you start down a hill. Shift

your weight uphill. Never go down a hill at high speed. Avoid going

down a hill at an angle, which would cause the vehicle to lean sharply

to one side. Drive straight downhill.

• Always follow proper procedures for crossing the side of a hill. Avoid

hills with excessively slippery or loose surfaces. Shift your weight

uphill. Never attempt to turn the ATV around on any hill until you've

mastered (on level ground) the turning technique outlined in this

manual. Avoid crossing the side of a steep hill when possible.

• Always use proper procedures if you stall or roll backwards while

climbing a hill. To avoid stalling, maintain a steady speed when

climbing a hill. If you stall or roll backwards, follow the special pro-

cedure for braking described in this manual. Always dismount on the

uphill side, or to either side if the ATV is pointed straight uphill. Turn

the ATV around and remount following the procedure described in

this manual.

Summary of Contents for Sportsman 9920629
















































































































































Search results

Summary of Contents for Sportsman 9920629

Reviews:

Related manuals for Sportsman 9920629

Brands by name

Popular brands

Polaris Sportsman 9920629, Owner'S Manual

Search results

Summary of Contents for Sportsman 9920629

Reviews:

Related manuals for Sportsman 9920629

Brands by name

Popular brands