manualshive.com logo in svg

Polaris Sportsman 850 2021, Owner'S Manual

Share
Download
Polaris Sportsman 850 2021 Owner'S Manual Download Page 133

TESTING

•  Test the battery using the PU-50296 battery tester.
•  Proper load testing of the battery requires special equipment and can be 

performed by your dealer.

AGM LOW MAINTENANCE BATTERIES

CHARGING

•  Polaris recommends using a BatteryMINDer® 2012 AGM - 2 AMP (

PN 

2830438

) charger, which can be ordered through your normal parts channel.

•  Nominal voltage is 12.6–12.8 Volts when fully charged. If the voltage falls 

below 12.5V, charge it immediately, or the battery runs the risk of sulfation.

MAINTENANCE

•  Never add electrolyte or distilled water to the battery. Doing so will damage 

the case and shorten the life of the battery.

•  If you do not drive the vehicle for more than TWO weeks, maintain the battery 

with the BatteryMINDer® 2012 AGM - 2 AMP (

PN 2830438

) charger.

•  If you plan to store the vehicle for ONE month or longer, remove the battery 

from the vehicle and store the battery in a cool / dry location. Continue to 
maintain the battery with the BatteryMINDer® 2012 AGM - 2 AMP (

PN 

2830438

) charger and inspect the battery every 60 days.

TESTING

•  If the test fails, fully charge the battery.
•  If the battery is too low to accept a charge, see the AGM Battery Charging - 

Deeply Discharged (Below 3 Volts) procedure in the Service Manual.

•  Proper load testing of the battery requires special equipment and can be 

performed by your dealer.

CAMBER AND CASTER

The camber and caster are non-adjustable.

REAR SPRING

The rear shock absorber spring is adjusted by rotating the adjuster either 
clockwise or counter-clockwise to increase or decrease spring tension.

Accessory springs are available through your POLARIS dealer.

131

MAINTENANCE

Summary of Contents for Sportsman 850 2021





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands