Polaris SLINGSHOT GRAND TOURING 2019 Owner'S Manual Download Page 65 | Manualshive

Page: 65 / 147

background image

CANCEL CRUISE CONTROL

To temporarily cancel the cruise control and allow use of the resume feature,
perform one of the following:

• depress the brake pedal or
• depress the clutch pedal

To cancel the cruise control and erase the set speed from memory, move the
ON/OFF/RES switch to OFF.

RESUME SPEED

1. Disengage the cruise control by depressing the brake pedal or clutch pedal.

NOTE

If you depress the throttle pedal to accelerate, the cruise control will resume

the previously set speed when the pedal is released.

2. Move the ON/OFF/RES switch to RES to resume operation at the previously

set speed.

NOTE

Moving the ON/OFF/RES switch to OFF will erase the set speed from memory

and disengage the cruise control.

INCREASE SPEED SETTING

Move and release the ON/OFF/RES switch to RES to increase the set speed in
approximately one MPH (1-2 km/h) increments. Move and hold the ON/OFF/
RES switch in the RES position to accelerate to a new SET speed. The speed
will reset when the switch is released or after a maximum acceleration of
approximately 10 MPH (16 km/h), whichever comes first.

REDUCE SPEED SETTING

Press and release the SET switch to decrease speed in approximately one MPH
(1-2 km/h) increments. Press and hold the SET switch to decelerate to a new
SET speed (resets when switch is released), or to the minimum cruise speed of
25 MPH (40 km/h).

63

Downloaded from

«
...
63
64
65
66
67
...
»

Summary of Contents for SLINGSHOT GRAND TOURING 2019




















































































































































Reviews:

No comments

Related manuals for SLINGSHOT GRAND TOURING 2019

Brand: Jeep Pages: 673

For 1985-1992 GM Cars and Trucks 17933

Brand: Edelbrock Pages: 4

PERFECTVIEW CAM80AHD

Brand: Dometic Pages: 196

Brand: Kia Pages: 54

Brand: Phonocar Pages: 2

Brand: Yakima Pages: 21

2004 Vibe Navigation System

Brand: Pontiac Pages: 44

MILSCO KIT# C746700

Brand: K&M Pages: 2

Brand: Car-Interface Pages: 25

2 Bike Carrier 977

Brand: Thule Pages: 6

Brand: HAUL MASTER Pages: 8

PRIME DESIGN URX-001-E

Brand: Safe Fleet Pages: 8

Quantum Wash'n'Wipe N30208

Brand: National Cycle Pages: 12

Magic Watch MWE-850-4DSM

Brand: Waeco Pages: 204

S90 - ACCESSORY PANEL

Brand: Volvo Pages: 166

Brand: S&B Filters Pages: 4

Brand: Mazda Pages: 3

Brand: Navman Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands